Furuno FR-1500 MARK-3 User Manual Download Page 106

Page: 106 / 125

-8.6-

HDG - Heading, deviation and variation

IMO Resolution A.382 (X). Heading (magnetic sensor reading), which if corrected for deviation, will

produce magnetic heading, which if offset by variation will provide true heading.

$--HDG, x.x, x.x, a, x.x, a*hh<CR><LF>

Checksum

Magnetic variation, degrees, E/W (see notes 2 and 3)

Magnetic deviation, degrees, E/W (see notes 1 and 3)

Magnetic sensor heading, degrees

* Not used

NOTES 1 To obtain magnetic heading:Add easterly deviation (E) to magnetic sensor reading

Subtract westerly deviation (W) from magnetic sensor reading

2 To obtain true heading:

Add easterly variation (E) to magnetic heading

Subtract westerly variation (W) from magnetic heading

3 Variation and deviation fields will be null fields if unknown.

HDT - Heading True

$--HDT, x.x, T*hh<CR><LF>

Checksum

Heading, degree true

* Not used

MTW - Water temperature

$--MTW, x.x, C*hh<CR><LF>

Checksum

Temperature, degrees C

* Not used

Summary of Contents for FR-1500 MARK-3






























































































































Search results

Summary of Contents for FR-1500 MARK-3

Reviews:

Related manuals for FR-1500 MARK-3

Brands by name

Popular brands

Furuno FR-1500 MARK-3, User Manual

Search results

Summary of Contents for FR-1500 MARK-3

Reviews:

Related manuals for FR-1500 MARK-3

Brands by name

Popular brands