manualshive.com logo in svg

Furuno FELCOM250, Installation Manual

Share
Download
Furuno FELCOM250 Installation Manual Download Page 13

1.  HOW TO INSTALL THE UNIT

1-7

2. Lay the rubber mat on the mounting base and put the antenna unit on the rubber 

mat, keeping in mind cable gland direction (standard direction is stern).

3. Fix the antenna unit with four sets of hexagonal bolts and nuts as shown below.

Note: 

Tighten first nut with torque 36.5 Nm, then tighten second nut with the same 

torque.

4. Connect the ground wire to the ground bolt.
5. For FB-1250-A/C, attach the radiation warning sticker (small) to the bow and stern 

sides of the antenna radome. If these locations are not suitable, attach the radia-
tion warning stciker (big) to the ship’s  body near the antenna radome.

6. Coat all bolts and nuts with silicone sealant to prevent electrolytic corrosion.
7. For FB-1500-A/C, restore the lifting lugs to their original positions.

Silicone sealant

Nut

Spring washer

Flat washer

Seal washer

Bolt

Silicone sealant

Rubber mat

Ground stud

Silicone sealant 

FB-1500-A/C only

Summary of Contents for FELCOM250






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands