Furuno eRideOPUS 6 User Manual Download Page 2

eRide

OPUS 6/

 

eRide

OPUS 7    GV-8620/ GV-8720 

Dead  Reckoning  User

s  Guide 

SE16-900-002-02 

FURUNO ELECTRIC CO., LTD. All rights reserved.

 

Important Notice 

 
No part of this manual may be reproduced or transmitted in any form or by any means, electronic or 
mechanical, including photocopying and recording, for any purpose without the express written permission of 
the publisher, FURUNO ELECTRIC CO., LTD. 
 
FURUNO ELECTRIC CO., LTD. reserves the right to make changes to its products and specifications without 
notice. 
 
You expressly acknowledge and agree that use of the "Application Note" is at your sole risk.   
This "Application Note" is provided 'AS IS' and without warranty of any kind and FURUNO expressly disclaims 
all other warranties, express or implied, including, but not limited to, the implied warranties of merchantability, 
fitness for a particular purpose and no infringement. 
 
FURUNO does not warrant that the functions contained in the "Application Note" will meet your requirements, 
or that the operation of the "Application Note" will be uninterrupted or error-free, or that defects in the 
"Application Note" will be corrected. 
 
Furthermore, FURUNO does not warrant or make any representations regarding the use or the results of the 
use of the "Application Note" in terms of their correctness, accuracy, reliability, or otherwise. 
No oral or written information or advice given by FURUNO authorized representative shall create a warranty or 
in any way increase the scope of this warranty. 
 
Without limiting the foregoing, FURUNO disclaims any and all express or implied warranties of any kind, and 
you expressly assume all liabilities and risks, for use or operation of the "Application Note", including without 
limitation. 
 
Should the "Application Note" prove defective, you assume the entire cost of all necessary servicing, repair or 
correction. 
 
Some jurisdictions do not allow the exclusion of implied warranties, so the above exclusion may not apply to 
you. 
 
All brand and product names are registered trademarks, trademarks or service marks of their respective 
holders. 
 

 

Summary of Contents for eRideOPUS 6
























Reviews: