Furrion 2021132274 User Manual Download Page 8

Terminal of anti-freezing
sensor of connecting
main board

Fixing frame
of temperature
sensing head

Panel Installation

1.

Press the left and right buckles on the decorative panel at
the same time to remove the decorative panel, as shown
in the following figure:

Left and right buckles
on the decorative
panel

Arrow direction on the panel
(vehicle head direction)

2. Take out the panel, place it according to the direction

indicated on the panel, pass the connecting wire of
display panel on the control box through the via hole on
the panel, install the panel on the fixing plate and fix it
tightly with 4 screws, as shown in the following figure:

Connecting wire
of display lamp board

Via hole on the panel

Connecting wire of
display lamp board

Screw (4)

3. Take out the decorative panel, make the arrow direction

face the head of RV, plug the connecting wire of display
lamp board with the connecting wire of display lamp
board of the decorative panel in place, and then install the
lamp board on the panel (when installing the decorative
panel, first clamp the two buckles in arrow direction on
the corresponding holes of the panel, and then clamp
the rear two buckles on the panel lock), as shown in the
following figure:

Plugging of connecting
wire of display lamp
board

Corresponding
buckles

4. After the air conditioning equipment is installed, turn on

the power supply of the equipment to conduct running
inspection. Before continuing the operation, read
operation instructions of the equipment.

Installation to the Top of RV

1.

The permanent wiring of air conditioning control box can
be introduced from the main incoming line of RV (routed
by the side wall), as shown in the following figure:

Panel

Air conditioner

Preventive wiring (trunking)

Main cable

Junction box

It's forbidden to insert other plugs into this circuit

Special plug

2. Special socket for air conditioning equipment shall be

arranged on the side wall of RV. The cable should be
connected to socket and fuse.

3. The main connecting cable must be resistant to oil, water

and ozone corrosion

English

Rev: 06-30-22

 

- 7 -

CCD-0005745 

Summary of Contents for 2021132274



















Reviews: