manualshive.com logo in svg

Funkwerk 800ATC-(200)-(200), Operation And Installation

Share
Download
Funkwerk 800ATC-(200)-(200) Operation And Installation Download Page 31

TRT800 / P/N 800ATC-(200)-(200)  

Operation and Installation 

 

 
 

31

Document-No: 03.2102.010.71e / Revision: 2.02

Step 

Display (Example) 

8.  With digit 9 and the following 

the Flight-ID is defined (e. g. 
DEOLK) 
 

Important: Without blanks or 
any special characters and 
also without dashes.

 

 

9.  The last digits of the line must 

be filled with blanks. 

 

10. Press 

. 

with the rotary knob you can now 
select „yes“ if a Ground Switch is 
installed, if not select “no” and 
proceed with step 11

 

 

11. Press 

. 

at this stage the respective 
speed category shall be 
selected by using the rotary 
knob. (see section 4.1.6) 

 

12. Press 

.  

at this stage a GPS receiver for 
ADS-B Out can be selected 
(Selectable by rotary knob).

 

 

13. Press 

. 

with

   

further Records can now 

be created and configured as 
described in the aforementioned 
steps 
at startup of the transponder one 
of the defined records with all 
associated configurations need to 
be selected 

 

 

Summary of Contents for 800ATC-(200)-(200)







































Reviews:

No comments

Brands by name

Popular brands

Load more brands