manualshive.com logo in svg

Funkwerk 800ATC-(200)-(200), Operation And Installation

Share
Download
Funkwerk 800ATC-(200)-(200) Operation And Installation Download Page 11

TRT800 / P/N 800ATC-(200)-(200)  

Operation and Installation 

 

 
 

11

Document-No: 03.2102.010.71e / Revision: 2.02

Value 

Meaning 

Remarks 

 

 

diamond 

Transponder is transmitting: 
Replies on Interrogations 
Extended Squitter 

(ADS-B out)

 

 

•

 Appears per reply 

7000 active 

Squawk 

 

I 

Transponder is locked by a 
ground station and will be 
directly addressed 

Lock Information (indicated 
as vertical dash below the 
diamond) 

PLL 

PLL Error 

Internal Error 

TRX 
DC 

Transmit Failure 
Low current 

 
Internal error 

FPG FPGA-Failure 

Internal 

error 

BAT 

Battery Power too low 

maybe battery/generator fault

IDT 

transmits Ident-Marking (SPI)  ID („Squawk Ident“) has been 

pressed – active for 18 s 

FL010 
FLerr 

Flight Level 
Invalid altitude measuring 

Flight Level (in 100 ft steps) 
Beyond -1000 .. 35 000 ft, 
C Mode gets active 

ACS Opertional 

Mode 

(STBY, A-S, ACS, AC, A) 

Modes see section 2.5 

0000 

Standby Squawk 

Could be changed with active 
Squawk by pressing 

  

F 
G 

in-flight 
on-ground 

Ground-Switch-Info 
(if installed/available) 

Cradle 
Off 

no AA (24bit-Address) 
configured 

Transponder works in A/C-
Mode (no Mode-S) 

 

Summary of Contents for 800ATC-(200)-(200)







































Reviews:

No comments

Brands by name

Popular brands

Load more brands