manualshive.com logo in svg

Funkwerk 800ATC-(200)-(200), Operation And Installation

Share
Download
Funkwerk 800ATC-(200)-(200) Operation And Installation Download Page 21

TRT800 / P/N 800ATC-(200)-(200)  

Operation and Installation 

 

 
 

21

Document-No: 03.2102.010.71e / Revision: 2.02

3.8 Antenna 

3.8.1 Antenna 

Selection 

•

  Recommended antennas: see section 3.11 Accessories 

•

  Choose an antenna type compatible with the vehicle and the 

mounting location. 

•

  Specified features depend on proper installation of the antenna. 

•

  The radiation pattern needs to be verified considering aircraft type 

and mounting location. 

•

  The electrical interference between the antenna and any other 

equipment must be taken into account in such a way that no 
reduction of the performance of any other system will occur. 

•

  Install only certified antennas! 

3.8.2 Installation 

Recommendation 

•

  Take note of the antenna manufacturer’s instructions. 

•

  The usually deployed Dipol- or Blade antennas necessarily require 

a high frequency capable solid metal ground plane at the antenna 
base.  

•

  For installation in composite aircrafts, ground planes are to be 

added. The ground plane should be as large as possible but in any 
case not smaller than 10 cm x 10 cm. If in doubt, please contact 
the aircraft manufacturer. 

•

  Keep away three feet from any other antenna. 

•

  Pursue mounting in vertical position under the belly in flight 

direction. 

Summary of Contents for 800ATC-(200)-(200)







































Reviews:

No comments

Brands by name

Popular brands

Load more brands