background image

1-3-2

DVD_SFNP

Chassis or Secondary Conductor

d

d'

Primary Circuit Terminals

AC Voltmeter
(High Impedance)

Exposed Accessible Part

B

One side of 
Power Cord Plug Prongs

Z

Safety Check after Servicing

Examine the area surrounding the repaired location for
damage or deterioration. Observe that screws, parts,
and wires have been returned to their original posi-
tions. Afterwards, do the following tests and confirm
the specified values to verify compliance with safety
standards.

1. Clearance Distance

When replacing primary circuit components, confirm
specified clearance distance (d) and (d’) between sol-
dered terminals, and between terminals and surround-
ing metallic parts. (See Fig. 1)

Table 1 : Ratings for selected area

Note: This table is unofficial and for reference only. 

Be sure to confirm the precise values.

2. Leakage Current Test

Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs)
and externally exposed accessible parts (RF termi-
nals, antenna terminals, video and audio input and
output terminals, microphone jacks, earphone jacks,
etc.) is lower than or equal to the specified value in the
table below. 

Measuring Method  (Power ON) :

Insert load Z between B (earth ground, power cord
plug prongs) and exposed accessible parts. Use an
AC voltmeter to measure across the terminals of load
Z. See Fig. 2 and the following table.

AC Line Voltage

Clearance Distance (d), (d’)

220 to 240 V

 

3 mm(d)

 

6 mm(d’) 

Table 2: Leakage current ratings for selected areas

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

AC Line Voltage

Load Z

Leakage Current (i)

One side of power cord plug 

prongs (B) to:

220 to 240 V

2k

Ω 

RES. 

Connected in 

parallel

i

0.7mA AC Peak

i

2mA DC

RF or

Antenna terminals

50k

 RES. 

Connected in 

parallel

i

0.7mA AC Peak

i

2mA DC

A/V Input, Output

Fig. 1

Fig. 2

Summary of Contents for DPVR-5600











Reviews: