background image

1-1-1

H9700SP

SPECIFICATIONS

< VCR Section >

Note: Nominal specs represent the design specs. All units should be able to approximate these – some will exceed
and some may drop slightly below these specs. Limit specs represent the absolute worst condition that still might
be considered acceptable; In no case should a unit fail to meet limit specs.

Description

Unit

Minimum

Nominal

Maximum

Remark

1. Video

    1-1. Video Output (PB)

Vp-p

0.8

1.0

1.2

SP Mode

    1-2. Video Output (R/P)

Vp-p

0.8

1.0

1.2

    1-3. Video S/N Y (R/P)

dB

40

45

SP Mode,

W/O Burst

    1-4. Video Color S/N AM (R/P)

dB

37

41

SP Mode

    1-5. Video Color S/N PM (R/P)

dB

30

36

SP Mode

    1-6. Resolution (PB)

Line

230

245

SP Mode

2. Servo

    2-1. Jitter Low

µ

sec

0.07

0.12

SP Mode

    2-2. Wow & Flutter

%

0.3

0.5

SP Mode

3. Normal Audio

    3-1. Output (PB)

 dBV

-9

-4

-3

SP Mode

    3-2. Output (R/P)

dBV

-9

-4

-1.5

SP Mode

    3-3. S/N (R/P)

dB

36

41

SP Mode

    3-4. Distortion (R/P)

%

1.0

4.0

SP Mode

    3-5. Freq. resp (R/P) at 200Hz

dB

-6

-2

SP Mode

                (-20dB ref. 1kHz) at 8kHz

dB

-8

-2

SP Mode

4. Tuner

    4-1. Video output

Vp-p

0.8

1.0

1.2

E-E Mode

    4-2. Video S/N

dB

39

44

E-E Mode

    4-3. Audio output

dB

-10

-6

-2

E-E Mode

    4-4. Audio S/N

dB

40

46

E-E Mode

5. Hi-Fi Audio

    5-1. Output

dBV

-12

-9

-4

SP Mode

    5-2. Dynamic Range

dB

70

85

SP Mode

    5-3. Freq. resp (6dB B.W)

Hz

20 ~ 20K 

SP Mode

Summary of Contents for DPVR-5600











Reviews: