14
15
OPERATION (cont.)
3.
From the Main Menu, using the up button
(8) and down buttons (6) select Battery Test
(fig. 12) and press enter button (7).
4.
From the Battery Test menu (fig. 13), use
the up and down buttons to select Car or
Scooter and press enter button (7).
5.
From the Battery Type menu, use the up and down buttons to select the desired
battery type.
–
Car options available (fig. 14).
–
Scooter options available (fig. 15).
Note:
Lithium-ion battery is only for Scooter
battery types not car.
6.
Press enter button (7) to confirm your selection.
Note:
The battery tester will test each battery according to the selected battery
system standard (see page 9 for description) and rating marked on the battery.
Main Menu
1. Battery Test
2. Cranking Test
3. Charging Test
4. Review Data
5. Print
6. System Setup
Battery Test
1. Car
2. Scooter
Battery Type
1. Regular Flooded
2. AGM Flat Plate
3. AGM spiral
4. GEL
5. EFB
Battery Type
Battery Test
1. Car
2. Scooter
1. Regular Flooded
2. Lithium Ion
3. AGM Flat Plate
4. AGM spiral
5. GEL
6. EFB
Fig. 12
Main Menu
1. Battery Test
2. Cranking Test
3. Charging Test
4. Review Data
5. Print
6. System Setup
Battery Test
1. Car
2. Scooter
Battery Type
1. Regular Flooded
2. AGM Flat Plate
3. AGM spiral
4. GEL
5. EFB
Battery Type
Battery Test
1. Car
2. Scooter
1. Regular Flooded
2. Lithium Ion
3. AGM Flat Plate
4. AGM spiral
5. GEL
6. EFB
Fig. 13
Main Menu
1. Battery Test
2. Cranking Test
3. Charging Test
4. Review Data
5. Print
6. System Setup
Battery Test
1. Car
2. Scooter
Battery Type
1. Regular Flooded
2. AGM Flat Plate
3. AGM spiral
4. GEL
5. EFB
Battery Type
Battery Test
1. Car
2. Scooter
1. Regular Flooded
2. Lithium Ion
3. AGM Flat Plate
4. AGM spiral
5. GEL
6. EFB
Fig. 14
Main Menu
1. Battery Test
2. Cranking Test
3. Charging Test
4. Review Data
5. Print
6. System Setup
Battery Test
1. Car
2. Scooter
Battery Type
1. Regular Flooded
2. AGM Flat Plate
3. AGM spiral
4. GEL
5. EFB
Battery Type
Battery Test
1. Car
2. Scooter
1. Regular Flooded
2. Lithium Ion
3. AGM Flat Plate
4. AGM spiral
5. GEL
6. EFB
Fig. 15
OPERATION (cont.)
7.
Use the up and down buttons to select the actual system standard (SAE,
DIN, IEC, EN, CA, MCA, JIS, BCI, CCA, GB), press enter button (7) to confirm
selection.
8.
Press the up and down buttons to input the battery cold cranking amps (CCA).
The battery Test Function is programmed with some additional settings which will
only be available if the results are close to set limit values:
– Battery Temperature:
This selection step
will appear if the battery result is around the
health limit value. Please select if the current
ambient temperature is above of below 0°C
(fig. 16).
If the temperature is confirmed to be below
0°C, the battery must be tested again at an
ambient temperature above 0°C (allow the
battery to match the ambient temperature
before testing).
– Charge State:
This selection step will
appear, if the voltage is detected to be at the
lower limit. Please select if the battery has
been charged before proceeding (fig. 17).
It is recommended the battery be charged
and retested after result has been acquired.
9.
Press the enter button (7) to confirm selection and start the test.
10.
Battery analysis will begin, it will take 3 seconds to display the battery test
results.
BAT Temperature
1. Below 0ºC
2. Above 0ºC
Charge State
1. Before Charge
2. After Charge
Fig. 16
BAT Temperature
1. Below 0ºC
2. Above 0ºC
Charge State
1. Before Charge
2. After Charge
Fig. 17
