manualshive.com logo in svg

Full Boar FBAST-100, Instruction Manual, Page: 23 / 28

Share
Download
Full Boar FBAST-100 Instruction Manual Download Page 23

23

OPERATION (cont.)

Diagnostic menu - Vehicle info:

 This function 

enables retrieval of Vehicle Identification 

No. (VIN), Calibration ID Nos. (CINs), 

Calibration Verification Nos. (CVNs) and In-use 

Performance Tracking on 2000 and newer 

vehicles that support Mode 9.

1.

  Use the Scroll button (7) to select Vehicle 

Information from the Diagnostic Menu and 

press Enter/Exit button (5) to confirm (fig. 

29).

2.

  An advisory message prompts you to turn 

ignition on with engine off. Press any button 

or wait a few seconds for information on the 

TFT colour screen (1) (fig. 30).

Note:

 If the vehicle does not support 

this mode a warning that the mode is not 

supported shows on the TFT colour screen (7).

3.

   From the Vehicle Information menu use the 

Scroll button (7) to select available item and 

press Enter/Exit button (5) to confirm (fig. 

31).

4.

   View retrieved vehicle information on the 

TFT colour screen (7) (fig. 32).

Vehicle Info

3/4

Vehicle ID Number
Calibration ID

Cal. Verf. Number

Previous Menu

Cal. Verf. Number

CVN1 ## ## ## ##

Diagnostic Menu

1/7

Read Codes
Erase Codes
View Freeze Frame
I/M Readiness

Vehicle Information

Vehicle Info.

Turn key on

with engine off!

Press any button to con.

Fig. 29

Vehicle Info

3/4

Vehicle ID Number
Calibration ID

Cal. Verf. Number

Previous Menu

Cal. Verf. Number

CVN1 ## ## ## ##

Diagnostic Menu

1/7

Read Codes
Erase Codes
View Freeze Frame
I/M Readiness

Vehicle Information

Vehicle Info.

Turn key on

with engine off!

Press any button to con.

Fig. 30

Vehicle Info

3/4

Vehicle ID Number
Calibration ID

Cal. Verf. Number

Previous Menu

Cal. Verf. Number

CVN1 ## ## ## ##

Diagnostic Menu

1/7

Read Codes
Erase Codes
View Freeze Frame
I/M Readiness

Vehicle Information

Vehicle Info.

Turn key on

with engine off!

Press any button to con.

Fig. 31

Vehicle Info

3/4

Vehicle ID Number
Calibration ID

Cal. Verf. Number

Previous Menu

Cal. Verf. Number

CVN1 ## ## ## ##

Diagnostic Menu

1/7

Read Codes
Erase Codes
View Freeze Frame
I/M Readiness

Vehicle Information

Vehicle Info.

Turn key on

with engine off!

Press any button to con.

Fig. 32

Summary of Contents for FBAST-100





























Reviews:

No comments