Fujitsu UTY-LNHUM Operating Manual Download Page 14

En-13

TROUBLESHOOTING

 WARNING

•  In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the electrical breaker and consult authorized service 

personnel. 

•  Merely turning off the unit’s power switch will not completely disconnect the unit from the power source. 

•  Always be sure to turn off the electrical breaker to ensure that power is completely off.

Before requesting service, perform the following checks:

Symptom

Problem

See Page

NORMAL

FUNCTION

Doesn’t operate immedi-
ately:

  If the indoor unit is stopped and then immediately started again, the 

compressor will not operate for about 3 minutes, in order to prevent 
fuse blowouts.

  Whenever the electrical breaker is turned off then on again the protec-

tion circuit will operate for about 3 minutes, preventing unit operation 
during that period.

Noise is heard:

  During operation or immediately after stopping the unit, the sound 

of water 

fl

 owing in the air conditioner’s piping may be heard. Also, 

noise may be particularly noticeable for about 2 to 3 minutes after 
starting operation (sound of refrigerant 

fl

 owing).

  During operation, a slight squeaking sound may be heard. This is 

the result of minute expansion and contraction of the front panel due 
to temperature changes.

● 

During Heating operation, a sizzling sound may be heard occasional. 
This sound is produced by the Automatic Defrosting operation.

14

Smells:

  Some smell may be emitted from the indoor unit. This smell is the 

result of room smells (furniture, tobacco, etc.) which have been taken 
into the indoor unit.

Mist or steam is 
emitted:

  During Cooling or Dry operation, a thin mist may be seen emitted 

from the indoor unit. This results from the sudden Cooling of room air 
by the cool air emitted from the indoor unit, resulting in condensation 
and misting.

● 

During Heating operation, the outdoor unit’s fan may stop, and steam 
may be seen rising from the unit. This is due to Automatic Defrosting 
operation.

14

Air

fl

 ow is weak or stops:

● 

When Heating operation is started, fan speed is temporarily very 
low, to allow internal parts to warm up.

● 

During Heating operation, if the room temperature rises above the 
temperature setting, the outdoor unit will stop, and the indoor unit will 
operate at very low fan speed. If you wish to warm the room further, 
set the temperature for a higher setting.

● 

During Heating operation, the indoor unit will temporarily stop opera-
tion (between 7 and 15 minutes) as the Automatic Defrosting mode 
operates. During Automatic Defrosting operation, the OPERATION 
Indicator Lamp will 

fl

 ash.

14

  During Dry mode, the indoor unit will operate at low speed; in order 

to adjust room humidity, the indoor unit’s fan may stop from time to 
time. Also, the fan may operate at very low speed when adjusting 
room humidity.

6

  During SUPER QUIET operation, the fan will operate at very low 

speed.

5

  In the monitor of AUTO operation, the fan will operate at very low 

speed.

6

  In case of Multi-type unit, if multiple units are operated in different 

operation modes as shown below, the units operated afterward will 
stop and the OPERATION Indicator Lamp (green) will 

fl

 ash.

Heating mode and cooling mode (or dry mode)
Heating mode and fan mode

15

Water is produced from 
the outdoor unit:

● 

During Heating operation, water may be produced from the outdoor 
unit due to Automatic Defrosting operation.

14

9374136131-02_OM.indb   13

9374136131-02_OM.indb   13

24/9/2553   15:18:47

24/9/2553   15:18:47

Summary of Contents for UTY-LNHUM

















Reviews: