Fujitsu PRIMERGY RX100 S8 Operating Manual Download Page 61

Page: 61 / 82

RX100 S8

Operating Manual

Starting up and operation

6.1.1.3

Indicators on the control panel

RST

Reset button

Pressing the reset button reboots the system.

CAUTION!

Risk of loss of data!

NMI

NMI button

CAUTION!

Do not press! Risk of loss of data! The NMI button may only
be used by service personnel.

ID indicator (blue)

Lights up blue when the system has been selected by pressing
the ID button. To deactivate, press the button again.

The ID indicator can also be activated via the ServerView
Operations Manager and the iRMC S4 Web interface and its
status reported to the ServerView Operations Manager and the
iRMC S4.

Power-on indicator (green)

Does not light up,

when the system is in power-off mode but

connected to the mains (AC connected).

Lights up green

during the power-on delay and while the system

is in normal operation (S0).

Summary of Contents for PRIMERGY RX100 S8



















































































Search results

Summary of Contents for PRIMERGY RX100 S8

Reviews:

Related manuals for PRIMERGY RX100 S8

Brands by name

Popular brands

Fujitsu PRIMERGY RX100 S8, Operating Manual

Search results

Summary of Contents for PRIMERGY RX100 S8

Reviews:

Related manuals for PRIMERGY RX100 S8

Brands by name

Popular brands