Fujitsu PRIMERGY RX100 S8 Operating Manual Download Page 64

Page: 64 / 82

Operating Manual

RX100

Starting up and operation

6.1.1.4

Indicators on the accessible drives/components

Optical drive activity indicator

Lights up green when the storage medium is being accessed.

Indicators on the hot-plug HDD module

Figure 8: Indicators on the hot-plug HDD module

1 HDD BUSY (green)

– Lit: HDD in active phase (drive active, drive being accessed)
– Does not light: HDD inactive

2 HDD FAULT (orange)

– Does not light: no HDD error
– Lights up: HDD Faulty or Rebuild Stopped (drive defective/needs

replacing, a rebuild process was stopped or the HDD module is not
correctly inserted)

– Slow flashing: HDD Rebuild (the data is being restored after changing

a drive)

햲햳

Summary of Contents for PRIMERGY RX100 S8



















































































Search results

Summary of Contents for PRIMERGY RX100 S8

Reviews:

Related manuals for PRIMERGY RX100 S8

Brands by name

Popular brands

Fujitsu PRIMERGY RX100 S8, Operating Manual

Search results

Summary of Contents for PRIMERGY RX100 S8

Reviews:

Related manuals for PRIMERGY RX100 S8

Brands by name

Popular brands