Fujitsu PRIMEQUEST 440 System Design Manual Download

Page: 69 / 280

C122-B001-02EN

2-11

2.3 IO_Unit

Table 2.5 IO_Unit external interfaces

2.3.1

BMM (COM port and USB port)

The BMM is a board that manages input and output of a partition. Each partition
requires one BMM. Two BMMs can be mounted in an IO_Unit:

Each partition requires one BMM.

A Video port, two USB ports, and a COM port are also mounted on the BMM.

2.3.2

HDD

The HDD is connected to the SCSI-BP (SCBP). Four U320 SCSI 3.5-inch HDDs,
which are hot-pluggable, can be mounted.

HDD mirroring is supported with optional software.

For details, see Section

6.4, "Redundancy of an HDD (Use of PRIMECLUSTER

GDS)."

External interface

Count

Remarks

USB

Mounted on optional BMM product

RS-232C

SCSI

Ultra320-SCSI

PCI-Box interface

Connected to optional PCI_Box

PCI-Box interface side band 4

Connected to optional PCI_Box

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands

Fujitsu PRIMEQUEST 440, System Design Manual

Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands