background image

6-10

C122-B001-02EN

CHAPTER 6 Redundant Configuration

 

6.4

Redundancy of an HDD (Use of PRIMECLUSTER 

GDS)

This section describes the redundant configuration for a HDD.

In the PRIMEQUEST series, an IO_Unit includes SCSI controllers, each of which has 
its own system.  Each SCSI controller connects to two HDDs.  An IO_Unit has four 
PCI cassette slots.  The unit also has a PCI_Box interface to allow for PCI slot 
expansion.

The I/O section does not have a redundancy function that would work independent 
from without software.  Therefore, to configure redundancy of the I/O function, 
combine multiple I/O devices for the intended purpose and install the software 
required to implement the redundancy function.  Optional software is required for 
redundancy.

Only Linux supports redundancy using optional software.  Windows supports 
mirroring using external RAID.

Figure 6.6  I/O  Configuration

XAI

XAI

XDI

XDI

XDI

XDI

.    .    .    .

.    .    .    .

Crossbar

SB#0

SB 

SB MMB

#0

#1 

#n

MMB

#1

IOU

#1

IOU

#n

LDX LDX LDX LDX

FLN

Memory

Memory

IOU#0

Manage-
ment 
LAN

Manage-
ment 
LAN

GbE SCSI

BMM#0

BMM#0

BMM#1

FLP#0

FLP#1

FLI

PXH#0

PXH#2

PXH#3

PXH#1

HDDx2

HDDx2

PCI card

PCI card

PCI card

PCI card

GbE SCSI

Private 
LAN

Private 
LAN

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Reviews: