Fujitsu PRIMEQUEST 2000 Series Installation Manual Download Page 146 | Manualshive

Page: 146 / 188

background image

Appendix D Notes on VMware installation
D.1 Building the RAID environment in the VMware internal disk.

122

CA92344-0536-04

Appendix D Notes on VMware installation

This appendix describes how to install VMware vSphere using the RAID environment configured in
internal HDD/SSD and it also provides notes on installation.
Hereafter, VMware vSphere is mentioned as VMware.

D.1 Building the RAID environment in the VMware internal

disk.

In the PRIMEQUEST 2000 series, RAID 0, RAID1, RAID 1E, RAID 5, RAID 6, RAID 10, RAID 50, RAID
60 are supported in internal HDD/SSD.
For details on building a RAID configuration using internal hard disks, see the SAS RAID controller Guide
below.

-

PRIMEQUEST 2400E/2800E/2800B
LSI MegaRAID SAS 2.0 Software

-

PRIMEQUEST 2400E2/2800E2/2800B2
LSI MegaRAID SAS 3.0 Software

D.2 Installing VMware Bundled Software

The bundled software is stored in ServerView Suite DVD(Tools) . The files are copied from ServerView
Suite DVD(Tools) and then used.
Further, the bundled software necessary for VMware vSphere are as mentioned below.

TABLE D.1 Installation of the software attached to VMware

Bundled software

Installation destination

ServerView ESXi CIM Provider

VMware ESXi

D.3 Setting of PCI Bus mode

VMware vShere 5 does not support segment mode. Set “PCI Address mode” menu in MMB Web-UI to
PCI Bus mode.
VMware vShere 6 supports segment mode, but segment mode and vt-d function cannot be used at the
same time.

-

If vt-d function is used for VMware vShere 6, set “PCI Address mode” menu in MMB Web-UI to PCI
Bus mode. For the detail of setting PCI Address mode, see “ [Mode] window” of “1.3.9 [Partition#x]
menu” of PRIMEQUEST 2000 series Tool Reference (CA92344-0539).

-

If segment mode is used for VMware vShere 6, disable vt-d function in EFI menu. For the detail of
setting PCI Address mode, see “ [Mode] window” of “3.4.3 [CPU Configuration] menu” of
PRIMEQUEST 2000 series Tool Reference (CA92344-0539).

«
...
144
145
146
147
148
...
»

Summary of Contents for PRIMEQUEST 2000 Series





























































































































































































Reviews:

No comments

Related manuals for PRIMEQUEST 2000 Series

Brand: Qlogic Pages: 2

Brand: Mesa Pages: 3

Brand: Inateck Pages: 26

Brand: Nvidia Pages: 62

Brand: Rosewill Pages: 29

Brand: StarTech.com Pages: 2

Brand: IOGear Pages: 60

Mini Port Replicator

Brand: Keyspan Pages: 41

Brand: Origin Instruments Pages: 12

Brand: D-Link Pages: 22

Brand: Macpower & Tytech Pages: 26

Brand: Targus Pages: 8

Brand: Belkin Pages: 25

USB Analog TV Stick II

Brand: KWorld Pages: 10

ZyXEL ZyAIR B-220

Brand: ZyXEL Communications Pages: 51

Brand: ZyXEL Communications Pages: 2

PowerLine PL-100

Brand: ZyXEL Communications Pages: 33

Brand: ZyXEL Communications Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands