Fujitsu MB90390 Series Hardware Manual Download Page 533

Page: 533 / 740

505

CHAPTER 23 CAN CONTROLLER

Figure 23.8-1 shows the flowchart determining message buffer (x) where received messages stored. It is

recommended that message buffers be arranged in the following order: message buffers in which each

AMSR bit is set to All Bits Compare, message buffers using AMR0 or AMR1, and message buffers in

which each AMSR bit is set to All Bits Mask.

Figure 23.8-1 Flowchart Determining Message Buffer (x) where Received Messages Stored

■

Receive Overrun

When a message is stored in the message buffer with the corresponding RCx being already set to "1", it will

results in receive overrun. In this case, the corresponding ROVRx bit in the receive overrun register

ROVRR is set to "1".

■

Processing for Reception of Data Frame and Remote Frame

●

Processing for reception of data frame

RRTRx of the remote request receiving register (RRTRR) becomes "0".

TREQx of the transmission request register (TREQR) becomes "0" (immediately before storing the

received message). A transmission request for message buffer (x) having not executed transmission will be

canceled.

Note:

A request for transmission of either a data frame or remote frame is canceled.

●

Processing for reception of remote frame

RRTRx becomes "1".

If TRTRx of the transmitting RTR register (TRTRR) is "1", TREQx becomes "0". As a result, the request

for transmitting remote frame to message buffer having not executed transmission will be canceled.

Note:

A request for data frame transmission is not canceled.

For cancellation of a transmission request, see Section "23.7 Transmission of CAN Controller".

Select the lo

est-numbered

message buffer.

YES

End

Start

Are message buffers

ith RCx set to "0"

ith AMSx.1 and AMSx.0 set to "00

found?

Select the lo

est-numbered

message buffer.

Summary of Contents for MB90390 Series





































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MB90390 Series

Reviews:

Related manuals for MB90390 Series

Brands by name

Popular brands

Fujitsu MB90390 Series, Hardware Manual

Search results

Summary of Contents for MB90390 Series

Reviews:

Related manuals for MB90390 Series

Brands by name

Popular brands