Fujitsu IP Centrex SRS-12i Administrator'S Manual Download Page 42

Page: 42 / 69

3-23

Fujitsu

IP Centr

ex T

elephone

Ser

vice Settings

Then, press ENTER.

Press either asterisk (*) to go back to sub-menu or OPTIONS to exit the
option menu.

To set-up Diffserv, follow the steps below:

1. Press OPTIONS, numeric key “2”, “3”, then ENTER.

2. Press ENTER.

3. Enter 8 digits of numeric Administrator password (see Administrator

Password Registration in chapter 4). Then ENTER.

*Factory default Administrator Password – 99999999

4. Press 2, then ENTER.

5. If Diffserv has been already set up, the last Diffserv level is displayed.

The default signaling value (101110) is set upon the shipment from the
manufacturer.

6. Key 6 digits of Diffserv, then press ENTER.

You can clear and re-enter the value by pressing CLEAR before saving the
value.

TOS S=7

V=6

COMPLETED

TOS / DIFFSERV SETTING
TOS S=4

V=0

ENTER ADM PASSWORD

ENTER ADM PASSWORD
********

1: TOS

2: DIFFSERV
(SELECT 1-2)

DIFFSERV SETTING
SIGNALING=101110

(0-1)

DIFFSERV SETTING
SIGNALING=101010

(0-1)

Summary of Contents for IP Centrex SRS-12i






































































Search results

Summary of Contents for IP Centrex SRS-12i

Reviews:

Related manuals for IP Centrex SRS-12i

Brands by name

Popular brands

Fujitsu IP Centrex SRS-12i, Administrator'S Manual

Search results

Summary of Contents for IP Centrex SRS-12i

Reviews:

Related manuals for IP Centrex SRS-12i

Brands by name

Popular brands