background image

8

INSTALLATION

Choosing a Location

IMPORTANT:

 Consult local and 

national building codes and ordinances for special 
installation requirements. Following location 
information will provide longer life and simplified 
servicing of the outdoor heat pump.

NOTICE:

 These units must be installed 

outdoors. No ductwork can be attached, or other 
modifications made, to the discharge grille. 
Modifications will affect performance or operation.

Operational Issues

IMPORTANT:

 Locate the unit in a 

manner that will not prevent, impair, or compromise 
the performance of other equipment installed 
in proximity to the unit. Maintain all required 
minimum distances to gas and electric meters, 
dryer vents, and exhaust and inlet openings. In 

WKHDEVHQFHRIQDWLRQDOFRGHVRUPDQXIDFWXUHUV·

recommendations, local code recommendations 
and requirements will take precedence.

•  Refrigerant piping and wiring should be properly 

sized and kept as short as possible to avoid 
capacity losses and increased operating costs.

•  Locate the unit where water runoff will not create 

a problem with the equipment. Position the unit 
away from the drip edge of the roof whenever 
possible. Units are weatherized, but can be 
affected by the following:

•  Water pouring into the unit from the junction 

of rooflines, without protective guttering. Large 
volumes of water entering the heat pump while 
in operation can impact fan blade or motor life, 
and coil damage may occur to a heat pump 
if moisture cannot drain from the unit under 
freezing conditions.

•  Freezing moisture or sleeting conditions can 

cause the cabinet to ice-over prematurely 
and prevent heat pump operation, requiring 
backup heat, which generally results in less 
economical operation.

•  Closely follow the clearance recommendations on 

page 8.

•  24" [61.0 cm] to the service panel access

•  60" [152.4 cm] above heat pump fan discharge 

(unit top) to prevent recirculation

•  6" [15.2 cm] to heat pump coil grille air inlets 

with 12" [30.5 cm] minimum recommended

Corrosive Environment

The metal parts of this unit may be subject to 
rust or deterioration if exposed to a corrosive 
environment. This oxidation could shorten the 

HTXLSPHQW·VXVHIXOOLIH

Corrosive elements include, but are not limited to, 
salt spray, fog or mist in seacoast areas, sulphur or 
chlorine from lawn watering systems, and various 
chemical contaminants from industries such as 
paper mills and petroleum refineries.

If the unit is to be installed in an area where 
contaminants are likely to be a problem, special 
attention should be given to the equipment location 
and exposure.

•  Avoid having lawn sprinkler heads spray directly 

on the unit cabinet.

•  In coastal areas, locate the unit on the side of the 

building away from the waterfront.

•  Shielding provided by a fence or shrubs may give 

some protection, but cannot violate minimum 
airflow and service access clearances.

•  Elevating the unit off its slab or base enough to 

allow air circulation will help avoid holding water 
against the base pan.

WARNING:

 

Disconnect all power 

to unit before starting maintenance. Failure to do 
so can cause electrical shock resulting in severe 
personal injury or death.

Regular maintenance will reduce the buildup of 

FRQWDPLQDQWVDQGKHOSWRSURWHFWWKHXQLW·VILQLVK

•  Frequent washing of the cabinet, fan blade, and 

coil with fresh water will remove most of the salt 
or other contaminants that build up on the unit.

•  Regular cleaning and waxing of the cabinet 

with a good automobile polish will provide some 
protection.

•  A good liquid cleaner may be used several times 

a year to remove matter that will not wash off with 
water.

Location

Summary of Contents for FO14R Series

















































Reviews: