background image

9

Location

INSTALLATION

Choosing a Location (cont.)

For Units With Space 
Limitations

In the event that a space limitation exists, we will 
permit the following clearances:

Single-Unit Applications: Clearances below 6" [15.2 
cm] will reduce unit capacity and efficiency. Do not 
reduce the 60" [152.4 cm] discharge or the 24" 
[61.0 cm] service clearances.

Multiple-Unit Applications: When multiple 
condenser grille sides are aligned, a 6" [15.2 
cm] clearance is recommended for 1.5 and 2 
ton models and 9" [22.9 cm] for 2.5 ton to 5 ton 
models. Two combined clearances below the 
minimum will reduce capacity and efficiency. Do not 
reduce the 60" [152.4 cm] discharge or 24" [61.0 
cm] service clearances.

Customer Satisfaction Issues

•  The heat pump should be located away from the 

living, sleeping, and recreational spaces of the 
owner and those spaces on adjoining property.

•  To prevent noise transmission, the mounting pad 

for the outdoor unit should not be connected to 
the structure and should be located a sufficient 
distance above grade to prevent ground water 
from entering the unit.

Unit Mounting

WARNING:

 

Secure an elevated unit 

and its elevating stand in order to prevent tipping. 
Failure to do so may result in severe personal 
injury or death.

Elevation of Unit

If elevating the heat pump, either on a flat roof or 
on a slab, observe the following guidelines.

•  If elevating a unit on a flat roof, use 4" × 4"  

[10.2 cm × 10.2 cm] or equivalent stringers 
positioned to distribute unit weight evenly and 
prevent noise and vibration.

•  Where snowfall is anticipated, raise the unit 

above the base pad to prevent ice buildup and 
coil damage. Mount the unit high enough to be 
above the average accumulated area snowfall.
See “Ground Snow Depth” chart on page 10 for 
representative snow depths.

NOTICE:

 Do not block drain openings on 

bottom of unit.

•  If unit must be elevated because of anticipated 

snowfall, secure unit and elevating stand such 
that unit and/or stand will not tip over or fall off. 
Keep in mind that someone may try to climb on 
unit.

Factory-Preferred Tie-Down 
Method for High Wind or 
Seismic Loads

IMPORTANT:

 The manufacturer-

approved/recommended method is a guide to 
securing equipment for wind and seismic loads.
Other methods might provide the same result, but 
the manufacturer method is the only one endorsed 
by the manufacturer for securing equipment where 
wind or earthquake damage can occur. Additional 
information is available in the PTS (Product 

7HFKQLFDO6XSSRUWVHFWLRQRIWKHPDQXIDFWXUHU·V

Web sites Rheemote.net, MyRheem.com, or 
MyRuud.com and can be found as a listing under 
each outdoor model. If you do not have access to 
this site, your distributor can offer assistance.

SERVICE PANELS/

INLET CONNECTIONS

/ HIGH & LOW

 VOLTAGE ACCESS

 ALLOW 24” [610 mm] OF 

CLEARANCE

ALLOW 60” [1524 mm]

 OF CLEARANCE

AIR INLET LOUVERS ALLOW

6” [152 mm] Min. OF 

CLEARANCE ALL SIDES

12” [305 mm] RECOMMENDED

ST-A1226-04-00

6"  MIN. (152 mm) FOR 1.5 & 2 TON

9"  MIN. (229 mm) FOR 2.5-5 TON

24"  MIN. (610 mm)

ST-A1226-03-00

ELEVATE ABOVE 

ANTICIPATE HIGH 

SNOW FALL

DO NOT BLOCK

 OPENINGS

IN BASE PAN

BASE PAD

(CONCRETE OR OTHER SUITABLE 

MATERIAL)

Summary of Contents for FO14R Series

















































Reviews: