Fujitsu F2MC-16LX Series Hardware Manual Download Page 485

Page: 485 / 710

467

CHAPTER 15 UART1

15.6.2

Operation in Clock Synchronous Mode
(Operation Mode 2)

When the UART1 is used in operation mode 2, the transfer mode is clock synchronous.

■

Operation in Clock Synchronous Mode

●

Format of transmit/receive data

In the synchronous mode, 8-bit data is transmitted/received on LSB-first.The start and stop bits are not

added to the transmit/receive data.

shows the data format for the clock synchronous mode.

Figure 15.6-5 Format of Transmit/Receive Data (Operation Mode 2)

●

Clock Supply

In the clock synchronous mode, count of clocks equal to the transmit and receive bits count must be

supplied.

•

When the internal clock (dedicated baud rate generator or internal timer) has already selected (SMR1

" to "101

" or "110

") and data is transmitted, the synchronous

clock for data reception is generated automatically.

•

When the external clock has already selected (SMR1 register bit 5 to 3: CS2 to CS0 = "111

"), the clock

for exact one byte must be supplied from outside after ensuring that data is present (SSR1 register bit

Transmission data

writing

Transmission by serial clock output

Mark level

SCK1 output

TXE

SOT1

(LSB)

(MSB)

Transmission data

Reception data

reading

Reception by serial clock input

Mark level

SCK1 input

RXE

SIN1

(LSB)

(MSB)

Reception data

Summary of Contents for F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for F2MC-16LX Series

Reviews:

Related manuals for F2MC-16LX Series

Brands by name

Popular brands

Fujitsu F2MC-16LX Series, Hardware Manual

Search results

Summary of Contents for F2MC-16LX Series

Reviews:

Related manuals for F2MC-16LX Series

Brands by name

Popular brands