Fujitsu F2MC-16LX Series Hardware Manual Download | Manualshive

Page: 107 / 710

background image

89

CHAPTER 3 CPU

3.5.16

Exception Processing Interrupt

The F

2

MC-16LX family performs exception processing when an undefined instruction is

executed.
Exception is basically the same as interrupt. When an exception is detected between
instructions, normal processing is suspended to perform exception processing.
Exception processing is performed when an unexpected operation is performed, and
should be used only for starting recovery software at debugging or in an emergency.

■

Exception processing

●

Operation of exception processing

The F

2

MC-16LX family treats all instruction codes not defined in the instruction map as undefined

instructions. If an undefined instruction is executed, the processing equal to the software interrupt

instruction "INT # 10" is performed.

At exception processing, the following processing is performed before the transition to interrupt

processing:

•

The values of dedicated registers (A, DPR, ADB, DTB, PCB, PC, PS) are saved to the system stack

•

The interrupt enable flag (CCR: I) cleared to "0" and interrupts disabled

•

The stack flag (CCR: S) set to "1"

The value of the program counter (PC) saved in the stack is a value of the address where undefined

instructions are stored. For instruction codes of 2 bytes or more, the value of the program counter (PC) is a

value of the address where instruction codes that can be identified as undefined are stored. When the type

of exception factor must be determined at exception processing, use the saved program counter (PC).

●

Return from exception processing

When the program counter (PC) indicates an undefined instruction, the interrupt return instruction (RETI)

from exception processing is executed to return to exception processing. Some measures such as

performing a software reset should be taken when returning from exception processing.

«
...
105
106
107
108
109
...
»

Summary of Contents for F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F2MC-16LX Series

Brand: National Instruments Pages: 162

Brand: Paradyne Pages: 112

Brand: Vonets Pages: 8

Brand: SMART Pages: 15

Brand: Black Box Pages: 37

PowerBeam AC Gen2

Brand: Ubiquiti Pages: 22

Brand: Acces I/O products Pages: 5

SINUS H PROFInet

Brand: Enertronica Santerno Pages: 34

Brand: iCEBOX Pages: 57

Brand: axing Pages: 52

FastTrak TX4000

Brand: Promise Technology Pages: 76

Brand: ASROCK Pages: 173

Brand: Rosewill Pages: 2

Masterliquid ML240L RGB

Brand: Cooler Master Pages: 18

Brand: Holtek Pages: 280

Brand: Vivotek Pages: 46

Brand: Westermo Pages: 22

ReadyNAS Duo v2

Brand: NETGEAR Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands