Fujitsu eclipse Operating Manual Download Page 20 | Manualshive

Page: 20 / 76

Fujitsu eclipse Operating Manual Download Page 20

Introducing the Encore/Eclipse Series

Common Functions

Page 16 MDE-3893P Encore® and Eclipse® Series Owner’s Manual · December 2011

Displaying Pump Totals for Encore/Eclipse Units

You can view pump totals for Encore and Eclipse units on the main and Price Per Unit (PPU)
displays by using the Manager’s Keypad located behind the Customer Interface Module (CIM)
door or Oven door on Side 1 of the dispenser. The keypad’s magnetic backing allows easier
handling and input.

Notes: 1) For Encore 300/500/550 and Eclipse units, to identify Side 1 (A) of the pump or

dispenser, refer to the section titled “Programming Orientation” in MDE-4732
Encore and Eclipse Series Owner’s Programming Manual.

2) For Encore S Series units, to identify Side 1 of the unit, see

.

The Manager’s Keypad is as shown in

Figure 3-7: Manager’s Keypad

1

4

7

CLEAR

2

5

8

0

3

6

9

F1

F2

ENTER

$

TOTAL

VOL

TOTAL

Manager’s Keypad

Note: To enter the Command Codes required to place the pump/dispenser in Standalone

mode or to program prices directly at the unit, refer to

“Standalone Mode”

on

To avoid potential electric shock, do not touch any wiring or electronic component(s)
behind the CIM/Oven Door or Main Door.

WARNING

The following table explains how to access the Manager’s Keypad.

For this Model Series

Use these Steps to Locate the Manager’s Keypad

Encore 300/500/550/S Series

• Open CIM door on Side 1 (A)
• Keypad is attached (by magnet) behind the door

Eclipse

• Open Oven door on Side 1 (A)
• Keypad is attached (by magnet) behind the door

«
...
18
19
20
21
22
...
»

Summary of Contents for eclipse













































































Reviews:

No comments