Fujitsu ECLIPSE CD5425 Owner'S Manual Download Page 113 | Manualshive

Page: 113 / 124

background image

113

Mounting instruction

Names of lead wires and destinations
(refer to Page 115)

●

Caution

●

Never connect the power supply to the speaker leads, otherwise it
causes damage to the main unit.

●

Note

●

To prevent unconnected leads from shorting out, insulate them by
wrapping their tips with electrical tape. Similarly, insulate the ends
of connected leads.
If an external amplifier is to be connected to the receiver, be sure
to ground its outside housing to the vehicle body (a metal part).

No.

Name

Wire color

Destination

1

ACC

Red

Connect where the power comes
on when the ignition is in the
ACC position.

2

B+

Yellow

Connect where the power is
constantly available, regardless
of the ignition switch's position.

3

Ground

Black

Connect where good body
grounding is available.

4

Antenna power supply

Blue

Connect to the automatic-antenna
control terminal of the vehicle.

5

Illumination power
supply

Orange/white Connect to where power comes on

when the headlights are turned on.

6

Control power supply

Blue/white

Connect to the control terminal
for the external amplifier, etc.

7

E-LAN terminal

Connect to the E-LAN terminal of
the CD changer, etc.

8 & 9

Line-out terminals

Connect to the RCA input
connectors of an external amplifier.

10

Line-out terminals (Nonfader)

Connect to the RCA input
connectors of an external
amplifier, or to the RCA output
connectors of a EQ.

11

Speaker leads

Connect them to their respective
speaker leads.

12

Genuine steering remote
control terminal

Connect to the vehicle steering
remote control.

* Compatible vehicle models

for installation: Vehicle with
voltage detection-type
steering remote control. Ask
your dealer for details.

CD5425.book 113 ページ２００４年１２月１１日　土曜日　午後５時９分

«
...
111
112
113
114
115
...
»

Summary of Contents for ECLIPSE CD5425





























































































































Reviews:

No comments

Related manuals for ECLIPSE CD5425

Brand: Hama Pages: 5

Brand: NAD Pages: 2

Brand: Yamaha Pages: 155

Brand: Brigmton Pages: 38

Satlook Micro G2

Brand: emitor Pages: 24

Brand: Zenith Pages: 26

Brand: JETI model Pages: 33

Brand: VDO Pages: 18

Brand: Acesori Pages: 2

Brand: Tecsun Pages: 34

Brand: K1EL Pages: 53

Brand: Harman Kardon Pages: 12

Brand: Integra Pages: 54

Brand: Aiwa Pages: 16

Brand: Audio System Pages: 2

Brand: Eclipse Pages: 141

Brand: StarTech.com Pages: 10

Brand: Salus Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands