Fujitsu ECLIPSE CD5425 Owner'S Manual Download

Page: 78 / 124

How to use an optional remote control

Switching playback modes

Press the [MODE] button.

Press the button to switch modes in the following sequence:

How to play the tuner

Select the tuner mode first.

Selecting the FM/AM band

Press the [BAND] or [TU] button.

Each press will switch tuner modes from FM1

➔

FM2

➔

FM3

➔

AM.

Modes can be switched by pressing the following buttons:
[TU] button :

The tuner mode is activated.

[DISC] button : The disc mode is activated.
[AUX] button : The AUX mode is activated.

●

It is not possible to switch between FM/AM mode and SIRIUS
with the remote control.

●

If the optional SIRIUS tuner is connected, the selections with
switch the mode from SR1

➔

SR2

➔

SR3

➔

SR4 in order.

[BAND] button

[TU] button

[MODE] button

[DISC] button

[AUX] button

Tuner

Disc

AUX

CD5425.book 78 ページ２００４年１２月１１日　土曜日　午後５時９分

Summary of Contents for ECLIPSE CD5425





























































































































Search results

Summary of Contents for ECLIPSE CD5425

Reviews:

Related manuals for ECLIPSE CD5425

Brands by name

Popular brands

Fujitsu ECLIPSE CD5425, Owner'S Manual

Search results

Summary of Contents for ECLIPSE CD5425

Reviews:

Related manuals for ECLIPSE CD5425

Brands by name

Popular brands