background image

En-1

 WARNING

•  The appliance shall be installed, operated and stored in a room with a 

fl

 oor area larger 

than X m².

Amount of refrigerant charge 

M (kg)

Minimum room area 

X (m

2

)

 1.22

-

1.22 < M 

 1.23

1.45

1.23 < M 

 1.50

2.15

1.50 < M 

 1.75

2.92

1.75 < M 

 2.0

3.82

2.0 < M 

 2.5

5.96

2.5 < M 

 3.0

8.59

3.0 < M 

 3.5

11.68

3.5 < M 

 4.0

15.26

(IEC 60335-2-40)

•  Installation of this product must be done by experienced service technicians or profes-

sional installers only in accordance with this manual. Installation by non-professional 
or improper installation of the product might cause serious accidents such as injury, 
water leakage, electric shock, or 

fi

 re. If the product is installed in disregard of the 

instructions in this manual, it will void the manufacturer’s warranty.

•  Do not turn on the power until all work has been completed. Turning on the power be-

fore the work is completed can cause serious accidents such as electric shock or 

fi

 re.

•  If refrigerant leaks when you are working, ventilate the area. If the leaking refrigerant 

is exposed to a direct 

fl

 ame, it may produce a toxic gas.

•  Installation must be performed in accordance with regulations, codes, or  standards for 

electrical wiring and equipment in each country, region, or the installation place.

•  Do not use means to accelerate the defrosting process or to clean, other than those 

recommended by the manufacturer.

•  This appliance is not intended for use by persons (including children) with reduced 

physical, sensory or mental capabilities, or lack of experience and knowledge, unless 
they have been given supervision or instruction concerning use of the appliance by a 
person responsible for their safety. Children should be supervised to ensure that they 
do not play with the appliance.

•  To avoid danger of suffocation, keep the plastic bag or thin 

fi

 lm used as the packaging 

material away from young children.

•  The appliance shall be stored in a room without continuously operating ignition 

sources (for example: open 

fl

 ames, an operating gas appliance or an operating 

electric heater).

•  Do not pierce or burn.
•  Be aware that refrigerants may not contain an odour.

 CAUTION

•  Read carefully all safety information written in this manual before you install or use the 

air conditioner.

•  Install the product by following local codes and regulations in force at the place of 

installation, and the instructions provided by the manufacturer.

•  This product is part of a set constituting an air conditioner. The product must not be 

installed alone or be installed with a device not authorized by the manufacturer.

•  Always use a separate power supply line protected by a circuit breaker operating on 

all wires with a distance between contact of 3 mm for this product.

•  To protect the persons, earth (ground) the product correctly, and use the power cable 

combined with an Earth Leakage Circuit Breaker (ELCB).

•  This product is not explosion proof, and therefore should not be installed in an explo-

sive atmosphere.

•  To avoid getting an electric shock, never touch the electrical components soon after 

the power supply has been turned off. After turning off the power, always wait 5 min-
utes or more before you touch the electrical components.

•  This product contains no user-serviceable parts. Always consult experienced service 

technicians for repairing.

•  When moving or relocating the air conditioner, consult experienced service technicians 

for disconnection and reinstallation of the product.

•  Do not touch the aluminum 

fi

 ns of heat exchanger built-in the indoor or outdoor unit to 

avoid personal injury when you install or maintain the unit.

•  Do not place any other electrical products or household belongings under the product. 

Condensation dripping from the product might get them wet, and may cause damage 
or malfunction to the property.

•  Be careful not to scratch the air conditioner when handling it.

AIR CONDITIONER
Duct type

Contents

1. SAFETY 

PRECAUTIONS 

.................................................................. 1

1.1. Precautions for using R32 refrigerant ......................................... 2

2. PRODUCT 

SPECIFICATION 

............................................................. 4

2.1. Installation tools .......................................................................... 4
2.2. Accessories ................................................................................ 4
2.3. Pipe requirement ........................................................................ 4
2.4. Electrical requirement ................................................................. 4
2.5. Optional parts ............................................................................. 5

3. INSTALLATION 

WORK 

..................................................................... 5

3.1. Selecting an installation location ................................................ 5
3.2. Installation dimensions ............................................................... 5
3.3. Installing the unit ......................................................................... 5
3.4. Drain installation ......................................................................... 7
3.5. Pipe installation .......................................................................... 9
3.6. Electrical wiring ......................................................................... 10
3.7. Remote controller setting .......................................................... 13

4.  OPTIONAL INSTALLATION WORK ................................................ 13

4.1. Optional kit installation .............................................................. 13
4.2. External input and output .......................................................... 13
4.3. Remote sensor (Optional parts) ............................................... 14
4.4. IR receiver unit (Optional parts) ................................................ 14
4.5. Auto louver grille (Optional parts) ............................................. 14
4.6. Other optional parts .................................................................. 14
4.7. Optional parts cable binding ..................................................... 15

5.  REMOTE CONTROL INSTALLATION ............................................. 15

5.1. Group control ............................................................................ 15
5.2. Multiple remote control ............................................................. 16
5.3. DIP switch 101 setting .............................................................. 16
5.4. Simultaneous multi-system operation ....................................... 17

6. FUNCTION 

SETTING...................................................................... 17

6.1.  Function details ........................................................................ 17

7. TEST 

RUN 

....................................................................................... 19

7.1.  Check items .............................................................................. 19
7.2. Operation method ..................................................................... 19

8. FINISHING 

...................................................................................... 19

9. CUSTOMER 

GUIDANCE 

................................................................ 19

10. ERROR CODES 

.............................................................................. 19

NOTES:

  This manual describes how to install the air conditioner described above. Handling 

and installation shall only be done by professionals as outlined in this manual.

1. SAFETY PRECAUTIONS

•  Be sure to read this manual thoroughly before installation.
•  The warnings and precautions indicated in this manual contain important information 

pertaining to your safety. Be sure to observe them.

•  Hand this manual, together with the operating manual, to the customer. Request the 

customer to keep them on hand for future use, such as for relocating or repairing the 
unit.

 WARNING

Indicates a potentially or imminently hazardous situation 
which, if not avoided, could result in death or serious injury. 

 CAUTION

Indicates a potentially hazardous situation that may result in 
minor or moderate injury or damage to property.

INSTALLATION MANUAL

PART No. 9374342532

[Original instructions] 

For authorized service personnel only.

English

Deutsch

Français

Español

Italiano

E

λλη

vIk

ά

Português

Ру

сский

Türkçe

Türkçe

9374342532_IM.indb   1

9374342532_IM.indb   1

2018/12/11   10:11:28

2018/12/11   10:11:28

Summary of Contents for ARXG-KLLAP Series





















Reviews: