- (01 - 27) -
W
AL
L M
OU
NT
ED T
YP
E
AS
G
07
-1
4L
U
W
AL
L M
OU
NT
ED T
YP
E
AS
G
07
-1
4L
U
FUNCTION SETTING
12.
INDOOR UNIT (Setting by remote controller)
12-1.
The function settings of the control of the indoor unit can be changed by this procedure according
•
to the installation conditions. Incorrect settings can cause the indoor unit malfunction.
After the power is turned on, perform the “FUNCTION SETTING” according to the installation
•
conditions using the remote controller.
The settings may be selected between the following two: Function Number or Setting Value.
•
Settings will not be changed if invalid numbers or setting values are selected.
•
PREPARATION
Turn on the power
•
* By turning on the power indoor units, so make sure the piping air-tight test and vacuuming have been conducted
before turning on the power.
* Also check again to make sure no wiring mistakes were made before turning on the power.
FUNCTION SETTING METHOD (for Wireless remote controller)
Perform the “FUNCTION SETTING” according to the installation conditions using the remote controller.
CAUTION
Confirm whether the wiring work for Outdoor unit has been finished.
Confirm that the cover for the electrical enclosure on the outdoor unit is in place.
This procedure changes to the function settings used to control the indoor unit according to the
•
installation conditions. Incorrect settings can cause the indoor unit to malfunction.
After the power is turned on, perform the “FUNCTION SETTING” according to the installation
•
conditions using the remote controller.
The settings may be selected between the following two: Function Number or Setting Value.
•
Settings will not be changed if invalid numbers or setting values are selected.
•
Refer to the installation manual enclosed with the remote control unit when the wired remote
•
control unit (option) is used.
Adjust the signal code of the indoor unit and the signal code of the remote controller.
•
Entering the Function Setting Mode
While pressing the POWERFUL button and SET TEMP. ( ) simultaneously, press the RESET button to enter the
function setting mode.
Selecting the Function Number and Setting Value
Press the SET TEMP. (
1.
/ ) buttons to select the function number. (Press the
10°C HEAT button to switch between the left and right digits.)
Press the POWERFUL button to proceed to setting the value. (Press the
2.
POWERFUL button again to return to the function number selection.)
Press the SET TEMP. (
3.
/ ) buttons to select the setting value. (Press the
10°C HEAT button to switch between the left and right digits.)
Press the MODE button, in the order listed to confirm the settings.
4.
Please confirm that the beep sounds.
Next, please press START/STOP (
5.
/
) button. Please confirm that the beep
sounds.
Press the RESET button to cancel the function setting mode.
6.
After completing the FUNCTION SETTING, be sure to turn off the power and turn
7.
it on again.
Function number
Setting
value
CAUTION
After turning off the power, wait 10 seconds or more before turning on it again.
The Function Setting does not become active unless the power is turned off
then on again.
Summary of Contents for AO*G07LUC
Page 10: ... 01 07 WALL MOUNTED TYPE AS G07 14LU WALL MOUNTED TYPE AS G07 14LU INSTALLATION PLACE Unit mm ...
Page 35: ...2 OUTDOOR UNIT SINGLE TYPE AO G07LUC AO G09LUC AO G12LUC AO G14LUC DTR_AO085E_01 2011 04 08 ...
Page 42: ... 02 06 OUTDOOR UNIT AO G07 14LU OUTDOOR UNIT AO G07 14LU MODEL AO G12LU AO G14LU ...
Page 51: ... 02 15 OUTDOOR UNIT AO G07 14LU OUTDOOR UNIT AO G07 14LU SOUND LEVEL CHECK POINT 88888 ...