Fujitsu Airstage VR-II ARUV12TLAV, Installation Manual

Page: 15 / 17

En-14
7.3 Function setting
• Function setting can be performed with the wired or wireless remote controller.
(The remote controller is optional equipment)
• Refer to the wired or wireless remote controller manual for detailed setting information. (Set
IU AD, REF AD SW to 0)
• Refer to “7.1. Setting the address” for indoor unit address and refrigerant circuit address
settings.
• Turn the power of the indoor unit on before starting the setting.
* Turning on the power to the indoor units initializes EEV, so make sure the piping air tight
test and vacuuming have been conducted before turning on the power.
* Also check again to make sure no wiring mistakes were made before turning on the
power.
Function details
Function
Function
number
Setting number Default Details
Filter
indicator
interval
11
00 Standard
○ Adjust the fi lter cleaning interval
noti fi cation. If the noti fi cation is too
early, change to setting 01. If the
noti
fi cation is too late, change to
setting 02.
01 Longer
02 Shorter
Filter
indicator
action
13
00 Enable
○
Enable or disable the fi lter indicator.
Setting 02 is for use with a central
remote controller.
01 Disable
02
Display only
on central
remote
controller
Cool air
tem-
perature
trigger
30
00 Standard
○
Adjust the cool air trigger tempera-
ture. To lower the trigger tempera-
ture, use setting 01. To raise the
trigger temperature, use setting 02.
01 Adjust (1)
02 Adjust (2)
Heat air
tem-
perature
trigger
31
00 Standard
○ Adjust the heat air trigger tempera-
ture. To lower the trigger tempera-
ture by 6 degrees C, use setting 01.
To lower the trigger temperature
by 4 degrees C, use setting 02. To
raise the trigger temperature, use
setting 03.
01 Adjust (1)
02 Adjust (2)
03 Adjust (3)
Auto
restart
40
00 Enable
Enable or disable automatic system
restart after a power outage.
* Auto restart is an emergency func-
tion such as for power failure etc.
Do not start and stop the indoor
unit by this function in normal
operation.
Be sure to operate by the control
unit, converter or external input
device.
01 Disable
○
Cool Air
Preven-
tion
43
00 Super low
○
Restrain the cold air fl ow with making
the air fl ow lower when starting heat-
ing operation. To correspond to the
ventilation, set to 01.
01
Follow the
setting on
the remote
controller
External
control
46
00 Start/Stop
○ Allow an external controller to start
or stop the system, or to perform an
emergency stop.
* If an emergency stop is performed
from an external controller, all re-
frigerant systems will be disabled.
* If forced stop is set, indoor unit
stops by the input to the external
input terminals, and Start/Stop by a
remote controller is restricted.
01
Emergency
stop
02 Forced stop
Error re-
port target
47
00 All
○
Change the target for reporting
errors. Errors can either be reported
in all locations, or only on the central
remote controller.
01
Display only
on central
remote
controller
Fan set-
ting when
cooling
thermostat
off
49
00
Follow the
setting on
the remote
controller
○
When set to 01, the fan stops when
the thermostat is off in cooling
operation. Connection of the wired
remote controller (2-wire type
or 3-wire type) and switching its
thermistor are necessary.
01 Stop
Function
Function
number
Setting number Default Details
Switching
func-
tions for
external
inputs and
external
outputs
terminals
60
00 Mode 0
○
• Set this function when connecting
the VRF system to a ventilator,
economizer, humidi
fi er, or other
external device.
• The connection terminal functions
can be changed depending on the
type of external device. For details
of the connection terminal func-
tions, see the Design & Technical
Manual.
* When an electric heater is con-
nected to this unit, "04 (Mode 4)
and "06 (Mode 6)" cannot be used.
Do not set them.
01 Mode 1
02 Mode 2
03 Mode 3
04* Mode 4
05 Mode 5
06* Mode 6
07 Mode 7
08 Mode 8
Control
switching
of external
heaters
61
00
Auxiliary
heater
control 1
○
Sets the control method for the exter-
nal heater being used. For details of
the control method, see the Design
& Technical Manual.
01
Auxiliary
heater
control 2
02
Heat pump
prohibition
control
03
Heater
selection
control using
outdoor tem-
perature 1
04
Heater
selection
control using
outdoor tem-
perature 2
Operating
tem-
perature
switching
of external
heaters
62
00 Setting 0
○
• Sets the temperature conditions
when the external heater is ON.
• For the temperature conditions,
see "Temperature conditions when
the external heater is ON". For a
more detailed explanation, see the
Design & Technical Manual
01 Setting 1
02 Setting 2
03 Setting 3
04 Setting 4
05 Setting 5
Temperature conditions when the external heater is ON
Temperature (t) when the external heater is ON = Room temperature - set temperature
Set value of function: 61
00 01 02 03 04
Set value of func-
tion: 62
00 t < -5.4°F (-3°C) t ≤ -0.9°F (-0.5°C)
01 t < -3.6°F (-2°C) t ≤ -1.8°F (-1°C)
02 t < -3.6°F (-2°C) t ≤ -3.6°F (-2°C)
03 t < -5.4°F (-3°C) t ≤ -5.4°F (-3°C)
04 t < -7.2°F (-4°C) t ≤ -7.2°F (-4°C)
05 t < -9.0°F (-5°C) t ≤ -9.0°F (-5°C)
8. TEST RUN
8.1 Test run using outdoor unit (PCB)
• Refer to the installation manual for the outdoor unit if the PCB for the outdoor unit is to be
used for the test run.
8.2 Test run using remote controller
• Refer to the installation manual for the remote controller to perform the test run using the
wireless remote controller.
• When the air conditioner is being test run, the OPERATION and TIMER indicators fl ash
slowly at the same time.