background image

En-2

Drain installation

21 21 

 CAUTION

Perform drain work in accordance with this Manual, and ensure that the drain water 

is properly drained. If the drain work is not carried out correctly, water may drip down 

from the unit, wetting the furniture.

When the outdoor temperature is 32 °F or less, do not use the accessory drain pipe 

and drain cap. If the drain pipe and drain cap are used, the drain water in the pipe may 

freeze in extremely cold weather. (Reverse cycle model only)

Outdoor unit to be fasten with bolts at the four places indicated by the arrows without fail.

Bottom side

Drain cap mounting place

Drain pipe mounting place

Since  the  drain  water  flows  out  of  the  outdoor  unit  during  heating  operation,  install  the 

drain  pipe  and  connect  it  to  a  commercial  16  mm  (5/8  in.)  hose.  (Reverse  cycle  model 

only)

When installing the drain pipe, plug all the holes other than the drain pipe mounting hole 

in the bottom of the outdoor unit with putty so there is no water leakage. (Reverse cycle 

model only)

               

Drain pipe mounting hole

Base

Drain pipe

Installation dimensions

21 21 

 CAUTION

Install the unit where it will not be tilted by more than 3˚. However, do not install the 

unit with it tilted towards the side containing the compressor.

When installing the outdoor unit where it may exposed to strong wind, fasten it 

securely.

Decide the mounting position with the customer as follows:

(1) Install the outdoor unit in a location which can withstand the weight of the unit and 

vibration, and which can install horizontally.

(2) Provide the indicated space to ensure good airflow.

(3) If possible, do not install the unit where it will be exposed to direct sunlight.

 (If necessary, install a blind that does not interfere with the airflow.)

(4) Do not install the unit near a source of heat, steam, or flammable gas.

(5) During heating operation, drain water flows from the outdoor unit.

Therefore, install the outdoor unit in a place where the drain water flow will not be 

obstructed. (Reverse cycle model only)

(6) Do not install the unit where strong wind blows or where it is very dusty.

(7) Do not install the unit where people pass.

(8) Install the outdoor unit in a place where it will be free from being dirty or getting wet by 

rain as much as possible.

(9) Install the unit where connection to the indoor unit is easy.

Single outdoor unit installation

21 21 11 

When the upward area is open

 

• When there are obstacles at the back side.

100 mm (4 in.)

or more

INSTALLATION WORK

21 

Please obtain the approval of the customer when selecting the location of installation 

and installing the unit.

Selecting an installation location

21 11 

 WARNING

Securely install the outdoor unit at a location that can withstand the weight of the unit. 

Otherwise, the outdoor unit may fall and cause injury.

Be sure to install the outdoor unit as prescribed, so that it can withstand earthquakes 

and typhoons or other strong winds. Improper installation can cause the unit to topple 

or fall, or other accidents.

Do not install the outdoor unit near the edge of a balcony. Otherwise, children may 

climb onto the outdoor unit and fall off of the balcony.

 CAUTION

Do not install the outdoor unit in the following areas:

Area with high salt content, such as at the seaside. It will deteriorate metal parts, 

 

causing the parts to fail or the unit to leak water.

Area filled with mineral oil or containing a large amount of splashed oil or steam, 

 

such as a kitchen. It will deteriorate plastic parts, causing the parts to fail or the 

unit to leak water.

Area that generates substances that adversely affect the equipment, such as 

 

sulfuric gas, chlorine gas, acid, or alkali. It will cause the copper pipes and brazed 

joints to corrode, which can cause refrigerant leakage.

Area containing equipment that generates electromagnetic interference. It will 

 

cause the control system to malfunction, preventing the unit from operating 

normally.

Area that can cause combustible gas to leak, contains suspended carbon fibers or 

 

flammable dust, or volatile inflammables such as paint thinner or gasoline. If gas 

leaks and settles around the unit, it can cause a fire.

Area that has heat sources, vapors, or the risk of the leakage of flammable gas in 

 

the vicinity.

Area where small animals may live. It may cause failure, smoke or fire if small 

 

animals enter and touch internal electrical parts.

Area where animals may urinate on the unit or ammonia may be generated.

 

Please install the outdoor unit without slant.

Install the outdoor unit in a well-ventilated location away from rain or direct sunlight.

If the outdoor unit must be installed in an area within easy reach of the general public, 

install as necessary a protective fence or the like to prevent their access.

Install the outdoor unit in a location that would not inconvenience your neighbors, as 

they could be affected by the airflow coming out from the outlet, noise, or vibration. If it 

must be installed in proximity to your neighbors, be sure to obtain their approval.

If the outdoor unit is installed in a cold region that is affected by snow accumulation, 

snow fall, or freezing, take appropriate measures to protect it from those elements. To 

ensure a stable operation, install inlet and outlet ducts.

Install the outdoor unit in a location that is away from exhaust or the vent ports that 

discharge vapor, soot, dust, or debris.
Install the indoor unit, outdoor unit, power supply cable, connection cable, and remote 

control cable at least 1 m (40 in.) away from a television or radio receivers. The 

purpose of this is to prevent TV reception interference or radio noise. (Even if they are 

installed more than 1 m (40 in.) apart, you could still receive noise under some signal 

conditions.)

Branch switch and 

circuit breaker

Branch switch and 

circuit breaker

1 m (40 in.) or more

1 m (40 in.) or more

If children under 10 years old may approach the unit, take preventive measures so 

that they cannot reach the unit.

Keep the length of the piping of the indoor and outdoor units within the allowable 

range.

For maintenance purposes, do not bury the piping.

9374747122_IM_En.indd   5

20/12/2553   13:09:06

Summary of Contents for AIR CONDITIONER

















Reviews: