manualshive.com logo in svg

Fujitsu Siemens Computers CELSIUS M430, Operating Manual, Page: 62 / 90

Share
Download
Fujitsu Siemens Computers CELSIUS M430 Operating Manual Download Page 62

System expansions

 

 

Installing a hard disk drive 

►

 

Take the new hard disk drive out of its packaging. 

►

 

Make the required settings (e.g. master-slave settings or SCSI-ID) on the drive. 

 

 

►

 

Secure the EasyChange rails on the side of the 
hard disk by inserting the upper pins of the 
EasyChange rail in the corresponding holes of the 
hard disk. 

 

1

 

 

►

 

Push the hard disk drive into the casing (1) until the EasyChange rails engage. 

►

 

Connect the data and power supply cables to the hard disk drive or to the hard disk drives. 

 

i

 

Connect the blue plug of the data cable to the connection on the mainboard. Connect the 
plug on the other end to the hard disk drive. 
For SCSI drives, connect the hard disk ports to the plug of the controller or of the 
mainboard. 

 

54 

A26361-K665-Z126-1-19, edition 1 

Summary of Contents for CELSIUS M430



























































































Reviews:

No comments