71
INZ-TN2ZPAF-E
9. SPECIFICATIONS
*HQHUDOVSHFL¿FDWLRQV
6WDQGDUG6SHFL¿FDWLRQV
Principle of measurement:
CH
4
, CO
2
;
Non-dispersion infrared-ray absorption
method
Single light source and single beams
(single beam system)
O
2
; Fuel cell O
2
analyzer
H
2
S
; Constant-potential electrolytic method
Measurable gas components and measuring range:
1st range
2nd range
CH
4
CO
2
H
2
S
0 - 20 vol%
0 - 100 vol%
0 - 100 vol%
0 - 2000 ppm
0 - 5000 ppm
0 - 25 vol%
0 - 20 vol%
0 - 500 ppm
0 - 10 vol%
O
2
Built in
fuel cell
0D[FRPSRQHQWVQFOXGLQJ2
2
.
7ZRPHDVXUHPHQWUDQJHVDUHSURYLGHGIRU
each component, and a user can switch
between them.
Measured value indication:
Digital indication in 4 digits
(LCD panel with LED back light)
,QVWDQWDQHRXVYDOXHRIHDFKFRPSRQHQW
Analog output signals:
4 to 20mA DC or 0 to 1V DC, isolated
internally from circuit and ground. Output
lines are non-isolated each other.; 12
RXWSXWVPD[
$OORZDEOHORDGIRUWRP$'&
$OORZDEOHORDG.IRUWR9'&
Digital output: (Option)
1c contact (24V DC/1A, resistive load)
PD[RXWSXWV
Instrument error, calibration error,
UDQJH LGHQWL¿FDWLRQ DXWR FDOLEUDWLRQ
status, solenoid valve drive for auto
calibration, High/Low limit alarm con-
tact output.
* All relay contacts are isolated mutually
and from the internal circuit.
Digital input: (Option)
Voltage contact (supply 12-24VDC (15mA
0D[0D[LQSXWV
Remote range change over, auto
calibration remote start, remote hold,
Isolated from the internal circuit with
photocoupler.
Power supply:
Voltage rating
; 100V to 240V AC
Allowable range
; 85V to 264V AC
Frequency
;
50Hz/60Hz
3RZHUFRQVXPSWLRQ 9$PD[
Operation conditions:
Ambient
temperature
;
5°C to 40°C (CH4, CO, and 0-2000
ppm H
2
S analyzers)
15°C to 40°C (other than the above)
$PELHQWKXPLGLW\
5+PD[
non-condensing
Storage conditions:
Ambient
temperature
;
-
Û&WRÛ&
$PELHQWKXPLGLW\
5+PD[
non-condensing
Dimensions (H × W × D):
[[PP
0DVV
$SSUR[NJPD[
Finish color:
Front panel; Cool gray (PANTON 1C-F)
Enclosure:
Steel casing, for indoor use
Material of gas-contacting parts:
Gas inlet/outlet; SUS304
Sample cell; SUS304,chloroprene rubber
Infrared-ray transmitting window; CaF2
,QWHUQDOSLSLQJ7RDURQ7HÀRQ3RO\SURS\O
-
ene
6ROHQRLGYDOYH686ÀXRURUXEEHU
Fuel cell O
2
analyzer cell : ABS resin
Gas inlet/outlet: Rc1/4 or NPT1/4 internal thread
$QDO\]HUSXUJHJDVÀRZUDWH/PLQ$QDO\]HUSXUJHZLWK
N
2
or air is indispensable)
Life time of fuel cell O
2
analyzer: 2 years
Life time of constant-potential electrolytic H2S sensor:
1 year (under an average ambient tem-
SHUDWXUHRIÛ&
2. Standard Functions
Output signal holding:
Output signals are held unchanged during
manual and auto calibrations by activation
of holding (turning “ON” its setting).
The values held are those just before
start calibration mode or setting value.
Usage is selectable.
Indication of instantaneous values will
not be held.
Switch ranges: The switch ranges function is available in
manual, auto, and remote modes. Only
preset switch method is effective.
Manual: Allows range to switch by key operation.
$XWR
$XWRPDWLFDOO\VZLWFKHGIURP¿UVWUDQJHWR
second range when the measured value
H[FHHGV)6RI¿UVWUDQJH
Automatically switched from second range
WR¿UVWUDQJHZKHQWKHPHDVXUHGYDOXH
GURSVWRRUOHVV¿UVWUDQJH
Remote: Voltage contact input
$OORZV UDQJH WR VZLWFK YLD DQ H[WHUQDO
signal when remote range switch input
is received.
When the contact input terminals for
each component are input voltage, the
¿UVWUDQJHLVVHOHFWHGDQGLWLVVZLWFKHG
to the second range when the terminals
are open.
* These switch range value are settable between
WKH¿UVWUDQJHDQGVHFRQGUDQJHYDOXHVORZKLJK
range values).
