FSA H1-EQ5AN Manual Download Page 1

Page: 1 / 12

Page

H1-EQ5AN

Undersink RO System

Contents

Technical Overview ...................................................................................................................................... 2

I. Important Notes ..................................................................................................................................... 2

II. Before You Purchase/Open .................................................................................................................. 2

III. Before You Begin Installation ............................................................................................................... 2

IV. What is Reverse Osmosis .................................................................................................................... 2

Installation Introduction ................................................................................................................................. 2

I. Working with Quick Connect Fittings ...................................................................................................... 2

II. Flushing ................................................................................................................................................ 3

Installing Connections .................................................................................................................................. 3

I. Feed Water Connection ......................................................................................................................... 3

II. Drain Clamp .......................................................................................................................................... 3

III. Drilling Faucet Hole - Stainless Steel Sink) .......................................................................................... 3

IV. Mounting the Faucet ............................................................................................................................ 3

................................................................................................................................................................. 4

V. Storage Tank Assembly ........................................................................................................................ 4

Connecting the RO System .......................................................................................................................... 4

I. Fittings ................................................................................................................................................... 4

II. Tubing ................................................................................................................................................... 4

System Start Up & Operation........................................................................................................................ 5

I. Plumber Commissioning Steps .............................................................................................................. 5

II. Client to Complete Commissioning ....................................................................................................... 5

III. Automatic Shut off ................................................................................................................................ 6

IV. Turning the System On/Off .................................................................................................................. 6

Maintenance ................................................................................................................................................. 6

I. Replacement Parts................................................................................................................................. 6

II. Replacement Cartridges ....................................................................................................................... 6

III. Testing Filters ...................................................................................................................................... 6

Troubleshooting ............................................................................................................................................ 7

Additional Extras........................................................................................................................................... 9

I. Water Hammer Arrester ......................................................................................................................... 9

II. Leak Shut Off Kit ................................................................................................................................. 10

Summary of Contents for H1-EQ5AN













Search results

Summary of Contents for H1-EQ5AN

Reviews:

Related manuals for H1-EQ5AN

Brands by name

Popular brands

FSA H1-EQ5AN, Manual

Search results

Summary of Contents for H1-EQ5AN

Reviews:

Related manuals for H1-EQ5AN

Brands by name

Popular brands