background image

resistance when trying to swivel 
the valve. 
3. If you screw the valve on and 
the collar ‘bottom’s out’ on the 
tap, you may need to add 
another washer (to bulk up the 
space). 

The unit is not producing any 
water? 

1. Water Supply is off or 
disconnected. 
2. Pre-Filter has a blockage 
3. Insufficient Water Pressure 
4. Blue Plug Still Installed 

1. Turn on the water supply and 
ensure there are no obstructions 
to the water flow. 
2. Disconnect the tube between 
the membrane and pre-filter (like 
the pre-flushing instructions) and 
run water at full pressure to see if 
water comes out of the filter. – If 
the water does not come out (or 
is very weak pressure) the filter 
may need to be changed. 
3. Reverse Osmosis required 
50psi (Minimum) to operate – 
70psi+ is ideal. If you have lower 
than 50psi pressure this unit may 
not be suitable for you. Low 
Pressure Membranes are 
available for an additional charge 
that will work down to 20psi. 
4. Remove the blue plug from the 
drinking water line. 

Water is coming out slowly 

Reverse Osmosis 

RO filtration is a slow process, 
depending on the system you 
have purchased, you will only get 
about 8 – 12L of water per hour. 

I am getting much more waste 
water than filtered water 

1. Water Pressure 
 
 
2. Water Quality 
 
 
3. Blockage 

1. Our units are designed to run 
at approx. 1:1 – 1:1.5 waste 
water ratio at 70 psi. If your 
pressure is lower than 70 psi, the 
production rate may decrease 
and cause more drain water than 
filtered water. 
2. If your inlet water quality is 
poor and contains higher salts 
and hardness the filter may 
produce lest water than the 
specified amount. 
3. If you have good pressure, 
and average water quality it is 
possible there is a small 
blockage somewhere in the 
system. Try to follow the water 
flow along the system, 
disconnecting 1 tube at a time to 
try and pinpoint where the water 
is ‘stopping’ 

High pH Reading 

1. Alkaline Filter 
 
 
2. GAC Filter 
 
 
3. Insufficient Testing Equipment 

1. Alkaline Filters are designed to 
increase the pH of the water. 
When the filter is new it will be 
high but will soon settle to the 
advertised levels after adequate 
flushing. 

Summary of Contents for GT1-70B












Reviews: