background image

Please read all sections of this manual and retain for future reference. 

 
 

This product has been certified as commercial cooking equipment and 

MUST

 be installed by 

professional personnel as specified.  Installation, maintenance and repairs should be performed 

by your FRYMASTER FACTORY AUTHORIZED SERVICE CENTER. 

 

 DANGER 

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any 

other cooking appliance. 

 

 DANGER 

Instructions explaining procedures to be followed 

MUST

 be posted in a prominent location in 

the event the operator detects a gas leak.  This information can be obtained from the local gas 

company or gas supplier. 

 

 

WARNING 

Improper installation, adjustment, alteration, service or maintenance can cause property 

damage, injury or death.  Read the installation, operating and maintenance instructions 

thoroughly before installing or servicing this equipment. 

 

 DANGER

 

Safe and satisfactory operation of your equipment depends on proper installation.  Installation 

MUST

 conform with local codes, or in absence of local codes, with the National Fuel Gas Code, 

ANSI Z223.1; The Natural Gas Installation Code, CAN/CGA-B149.1; The Propane Installation 

Code, CAN/CGA-B149.2; or The latest edition of the National Electric Code, N.F.P.A. 70. 

 

NOTICE 

IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS ENODIS 

EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED 

DIRECTLY FROM FRYMASTER/DEAN, OR ANY OF ITS AUTHORIZED SERVICE CENTERS, 

AND/OR THE PART BEING USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS 

WARRANTY WILL BE VOID.  FURTHER, FRYMASTER/DEAN AND ITS AFFILIATES WILL NOT BE 

LIABLE FOR ANY CLAIMS, DAMAGES OR EXPENSES INCURRED BY THE CUSTOMER WHICH 

ARISE DIRECTLY OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INSTALLATION OF 

ANY MODIFIED PART AND/OR PART RECEIVED FROM AN UNAUTHORIZED SERVICE CENTER. 

 

 DANGER  

The crumb tray in fryers equipped with a filter system must be emptied into a fireproof container 

at the end of frying operations each day. Some food particles can spontaneously combust if left 

soaking in certain shortening material.  Additional information can be obtained in the filtration 

manual included with the system. 

 

NOTICE 

The Commonwealth of Massachusetts requires any and all gas products to be installed by a 

licensed plumber or pipe fitter. 

 

Summary of Contents for YSCFC24 Series









































Reviews: