manualshive.com logo in svg

Frymaster FilterQuick 5FQG30U, Installation, Operation And Maintenance Manual

Share
Download
Frymaster FilterQuick 5FQG30U Installation, Operation And Maintenance Manual Download Page 47

 

6-7 

Code

 

ERROR MESSAGE

 

EXPLANATION

 

E22 

OIL IN PAN ERROR 

Oil may be present in the filter pan. 

E23 

CLOGGED DRAIN (Gas) 

Vat did not empty during filtration 

E24 

OIL LEVEL SENSOR FAILED (Gas) 

Oil level sensor failed. 

E25 

RECOVERY FAULT 

Recovery time exceeded maximum time limit. 
Recovery time should not exceed 2:25 for gas.

E27 

LOW TEMP ALARM 

Oil temperature has dropped 30°F (17°C) 
lower than setpoint in idle mode or 45°F 
(25°C) in cook mode. (This message may 
appear if a product is dropped and the start 
cook button is not pressed immediately or if 
too large of cook loads are dropped.) 

E28 

HIGH TEMP ALARM 

Oil temperature has risen 40°F (22.2°C) higher 
than 
setpoint. If temperature continues to rise, the high 
limit will shut the burner off when temperature 
reaches 425°F (218°C) Non-CE or 395°F (202°C) 
CE. 

 

6.2.7  HIGH-LIMIT TEST MODE 

 

The high-limit test mode is used to test the high limit circuit.  The high-limit test will destroy the oil.  
It should only be performed with old oil. Shut the fryer off and call for service immediately if the 
temperature reaches 460°F (238°C) without the high-limit tripping and the computer displays 

high 

LIMIT FAILURE

 alternating with 

DISCONNECT POWER

 with an alert tone during testing. 

 

The test is cancelled at any time by turning the fryer off.  When the fryer is turned back on, it returns 
to the operating mode and displays the product. 

 

1.  Press and hold the check (

)

 button until 

MAIN MENU

 is displayed followed by 

PRODUCT 

SETUP

.  

 

 

 

2.  Press the left arrow (

) button until 

TECH MODE

 is displayed.  

 
3.  Press the check (

) button. 

 
4.  Enter 3000.   
 
5.  Press the left arrow (

) button until 

HI LIMIT TEST

 is displayed.   

 
6.  Press the check (

) button.  

 
The controller displays 

HIGH LIMIT YES/NO

. 

 
7.   Press the up arrow (

) button.  

 
8.  The controller displays 

PRESS AND HOLD CHECK

.   

Summary of Contents for FilterQuick 5FQG30U























































Reviews:

No comments

Brands by name

Popular brands

Load more brands