Frymaster FilterQuick 5FQG30U Installation, Operation And Maintenance Manual Download Page 19 | Manualshive

Page: 19 / 54

background image

2-9

Switching to a different type of gas without installing the proper conversion components
may result in fire or explosion. NEVER ATTACH THIS APPLIANCE TO A GAS SUPPLY
FOR WHICH IT IS NOT CONFIGURED!

Conversion of this appliance from one type of gas to another should only be performed
by qualified, licensed, and authorized installation or service personnel, as defined in
Section 1.7 of this manual.

FilterQuick™ FQG30 series gas fryers manufactured for non-CE countries use different burners for each
type gas. The burners in fryers built for Propane gas have a special gray-colored coating on the burner
tiles to enable them to withstand the higher caloric value of the Propane gas. Burners designed for use in
propane units may be used in natural gas applications, but not vice versa.

Non-CE Gas Conversion Kits

Natural Gas to Propane (LP) Gas

Propane (LP) Gas to Natural Gas

Full Vat PN 826-2965

Full Vat PN 826-2967

Dual Vat PN 826-2966

Dual Vat PN 826-2968

Non-CE Gas Conversion Kits for Australia

Natural Gas to Propane (LP) Gas

Propane (LP) Gas to Natural Gas

Full Vat PN 826-2969

Full Vat PN 826-2971

Dual Vat PN 826-2970

Dual Vat PN 826-2972

Units manufactured for export to CE countries are equipped with “universal” burners that may be used
with either Natural (G20, G25) gas or Butane (G30) and Propane (G31) gasses.

CE Gas Conversion Kits for Units with Gas Valve 810-1715

G20 or G25 (Natural) to G30 or G31 Gas:

G30 or G31 to G20 or G25 (Natural) Gas:

PN 826-2975

PN 826-2976

CE GAS CONVERSION INSTRUCTIONS

1. Between G20- and G25-type Natural Gas, adjust the gas pressure at the regulator. (Refer to the CE

Standard Burner Manifold Gas Pressure Chart.) Do not change the orifice.

2. Between a 2

nd

family (G20 or G25) and a 3

rd

family gas (G30 Butane or G31 Propane):

a. Change the orifices.

b. Adjust the manifold pressure.

3. Remove the old rating plate and return to Frymaster. Affix the new rating plate included with the

conversion kit in place of the old rating plate stating the gas has been converted.

«
...
17
18
19
20
21
...
»

Summary of Contents for FilterQuick 5FQG30U























































Reviews:

No comments

Related manuals for FilterQuick 5FQG30U

Brand: TEAM CUISINE Pages: 17

Brand: LOCO COOKERS Pages: 18

Brand: Gazi Pages: 15

Brand: TEFAL Pages: 12

Brand: Häfele Pages: 17

Brand: FAURE Pages: 24

Brand: ADC Pages: 22

Brand: ADC Pages: 20

Brand: ADC Pages: 24

Brand: Rival Pages: 12

Brand: Frigidaire Pages: 10

FAQE7077KB - 7.0 CF Chrome TRIM Drum 7 Cycles

Brand: Frigidaire Pages: 18

Brand: Frigidaire Pages: 3

Brand: Frigidaire Pages: 2

FAQE7011KW - 7 cu. Ft. Cycle Electric Dryer Drum

Brand: Frigidaire Pages: 18

Brand: Frigidaire Pages: 2

Brand: Frigidaire Pages: 22

Brand: Frigidaire Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands