Frymaster FilterQuick 5FQG30U Installation, Operation And Maintenance Manual Download Page 46

Page: 46 / 54

6-6

One vat doesn’t top off.

A. Filter error exists.
B. Service required error exists
C. Solenoid, pump, pin issue, RTD

or ATO issue.

A. Clear filter error properly. If problem persists

call your FAS for assistance.

B. Call your FAS for assistance.
C. Call your FAS for assistance.

Controller displays

TOPOFF OIL

EMPTY /

CONFIRM

Top off system out of oil.

Fill top off system with oil and press the



(CONFIRM) button. Once the JIB is replaced press
and hold the orange reset button for ten (10)
seconds to reset top off system.

6.2.6 Error Log Codes (For FilterQuick™ Controller Only)

Code

ERROR MESSAGE

EXPLANATION

E03

ERROR TEMP PROBE FAILURE

Temp probe reading out of range

E04

HI 2 BAD

High limit reading is out of range.

E05

HOT HI 1

High limit temperature is past more than 410

(210

C), or in CE countries, 395

F (202

E06

HEATING FAILURE

A component has failed such as controller,
interface board, gas valve, ignition module or
open-high limit.

E07

ERROR MIB SOFTWARE

Internal MIB software error

E08

ERROR ATO BOARD

ATO board connection lost; ATO board failure

E09

ERROR PUMP NOT FILLING

Dirty paper/pad and it needs changed or it was
bypassed; filter pump problem

E10

ERROR DRAIN VALVE NOT OPEN

Drain valve was trying to open and
confirmation is missing

E11

ERROR DRAIN VALVE NOT CLOSED

Drain valve was trying to close and
confirmation is missing

E12

ERROR RETURN VALVE NOT OPEN

Return valve was trying to open and
confirmation is missing

E13

ERROR RETURN VALVE NOT CLOSED

Return valve was trying to close and
confirmation is missing

E14

ERROR AIF BOARD

MIB detects AIF missing; AIF board failure

E15

ERROR MIB BOARD

Cooking controller detects MIB connections
lost; Check software version on each
controller. If versions are missing, check CAN
connections between each controller; MIB
board failure

E16

ERROR AIF PROBE

AIF RTD reading out of range

E17

ERROR ATO PROBE

ATO RTD reading out of range

E20

INVALID CODE LOCATION

SD card removed during update

E21

FILTER PAPER PROCEDURE ERROR
(Change Filter Paper)

25 hour timer has expired or a dirty filter may
be causing an incomplete filtration.

Summary of Contents for FilterQuick 5FQG30U























































Search results

Summary of Contents for FilterQuick 5FQG30U

Reviews:

Related manuals for FilterQuick 5FQG30U

Brands by name

Popular brands

Frymaster FilterQuick 5FQG30U, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for FilterQuick 5FQG30U

Reviews:

Related manuals for FilterQuick 5FQG30U

Brands by name

Popular brands