Frymaster 17EC Operating Instructions Manual Download Page 1

3-1

ELECTRIC COOKER MODELS 17EC, 17ECS, ESW AND EWBS

CHAPTER 3:  OPERATING INSTRUCTIONS

3.1

Spaghetti

 

Magic II Controller (As Used on 17EC and 17ECS Units)

1

2

3

4

5

6

9

8

7

S

PAGHETTI

M

AGIC

 II 

®

SOLID

SOLID

SOLID

SOLID

STATE

STATE

STATE

STATE

1

Numeric Keypad

6

Skim Switch (w/Autoskim only)

2

Boil Mode Indicator

7

Timer Start Switch

3

Boil Mode Switch

8

Simmer Mode Switch

4

Power Switch

9

Simmer Mode Indicator

5

LED  Display

3.1.1

Introduction

 

CAUTION

The Spaghetti Magic II (SMS II) computer used in 17EC/17ECS units is specially

configured for them.  The programming and operation of the 17EC/17ECS SMS II

computer are different than those of the SMS II computers used in other products.

  

The computers are not interchangeable.

The Spaghetti Magic II computer allows the operator to specify a specific cook time in minutes and
seconds, then initiate a cooking cycle. The computer is configured for both automatic filling
(Autofill) and automatic skimming (Autoskim) features.

When in the 

BOIL

 mode, the heating element is energized at all times.  It is used when actually

cooking pasta.

The 

SIMMER

 mode feature maintains the water temperature just below boiling (approximately

195ºF/90.6ºC), which conserves energy and water.  This feature is designed for rethermalizing previ-
ously cooked packaged products, and for keeping the cooker in standby.

The 

SKIM

 feature, when selected, adds water for approximately 3 seconds once a minute.  It causes

the water to overflow into the drain, carrying floating starch with it.  (A buildup of starch reduces the
efficiency of the cooker and can cause erroneous temperature and water level sensing.)

Summary of Contents for 17EC










Reviews: