background image

5

Stay Clear of Rotating Drivelines 

 

TS1644-UN-22AUG95                                                                          H96219-UN-29APR10

 

 

Entanglement in rotating driveline can cause serious injury or death. 

Keep tractor master shield and driveline shields in place at all times. Make 

sure rotating shields turn freely. 

Wear close fitting clothing. Stop the engine and be sure that PTO driveline 

is stopped before making adjustments, connections, or cleaning out PTO 

driven equipment. 

Do not install any adapter device between the tractor and the primary 

implement PTO drive shaft that will allow a 1000 rpm tractor shaft to power 

a 540 rpm implement at speeds higher than 540 rpm. 

Do not install any adapter device that results in a portion of the rotating 

implement shaft, tractor shaft, or the adapter to be unguarded. The tractor 

master shield shall overlap the end of the splined shaft and the added adaptor 

device as outlined in the table. 

PTO Type 

Diameter 

Splines n ± 5 mm (0.20 in.) 

35 mm (1.378 in.) 

85 mm (3.35 in.) 

35 mm (1.378 in.)  21 

85 mm (3.35 in.) 

45 mm (1.772 in.)  20 

100 mm (4.00 in.) 

 

 

 

Summary of Contents for wc1105

























Reviews: