Fronius Symo Hybrid 3.0 Installation Instructions Manual Download Page 3

Contents

Installation location and position

4

Explanation of safety notices

4

Safety

4

Proper use

5

Choosing the location of the inverter

6

Installation position of inverter

8

Fitting the inverter mounting bracket

10

Safety

10

Selecting wall plugs and screws

10

Recommended screws

10

Opening the inverter

10

Do not warp or deform the mounting bracket

11

Fitting the mounting bracket to a wall

12

Installing the mounting bracket on a mast or beam

12

Fitting the mounting bracket to metal supports

13

Connecting the inverter to the public grid (AC side)

14

Safety

14

Monitoring the grid

14

AC terminals

15

Type of AC cable

15

Preparing the aluminium cables for connection

15

Cross section of the AC cable

16

Requirements for the neutral conductor

16

Connecting the inverter to the public grid (AC)

16

Routing the AC cables

17

Maximum fuse rating on alternating current side

18

Connecting solar module strings to the inverter

19

Safety

19

General comments regarding solar modules

20

DC terminals

20

Connecting aluminium cables

20

Do not ground the poles of the solar modules

21

Solar module strings - checking the polarity and voltage

21

Connecting solar module strings to the inverter (DC)

21

Routing the DC cables

23

Connecting the battery to the inverter

25

Connecting the battery DC cables to the inverter

25

Overview of Fronius Energy Package DC cabling

27

Connecting the Modbus cables to the inverter

27

Terminating resistor for Modbus cable

28

Attaching the inverter to the mounting bracket

30

Attaching the inverter to the mounting bracket

30

Starting for the first time

32

Starting the inverter for the first time

32

Activating the emergency power function

34

Prerequisites for emergency power mode

34

Accessing the CONFIG menu

34

Selecting alternative (emergency power) setup

35

Fronius Ohmpilot and emergency power mode

35

Installing Fronius system monitoring – Overview

36

Safety

36

Starting for the first time

36

Information to help you work through the Solar Web wizard

38

Notes regarding maintenance

39

Maintenance

39

Cleaning

39

3

EN

Summary of Contents for Symo Hybrid 3.0









































Reviews: