background image

12

SILICONE

LUBRICANT

1.

2.

3.

4.

5.

1.

2.

3.

POOL FROG

®

 Cycler Maintenance 

Replacing the Control Dial O-Rings

Using a needle nose pliers, 
find the snap ring tail located 
at approximately the five 
o’clock position under the 
control dial.  

Pull down and out of the 
groove.

Using a large screwdriver, 
loosen the control dial. 
Carefully pry the dial until it 
pulls out.

Carefully replace the rubber 
o-ring without stretching it. 
Apply silicone lubricant, that 
came with your POOL FROG 
XL PRO®, on o-ring.

Push control dial completely 
into the housing and turn the 
dial to setting 2.

Replacing Cap O-Ring

Lubricate o-ring often with 
silicone lubricant that 
came with your POOL FROG 
XL PRO®. DO NOT USE 
petroleum based lubricants.

Replacing Knobs

Replace knob in back or on cap 
of both POOL FROG XL PRO

®

 

Cyclers by unscrewing old one 
and screwing in new one. 

Hold cap in front of you 
upside down with the o-ring 
groove facing up. Place one 
end of o-ring into cap groove 
at the point closest to you. 
Hold o-ring down with the 
thumb and index finger of 
one hand.

Take hold of the far end of 
the o-ring with the thumb 
and index finger of the other 
hand. Roll o-ring slightly 
back towards you as you 
stretch the o-ring into the 
remainder of the cap groove.

12

Insert the non-lipped end 
of snap ring into the groove 
opening beginning at the 
5 o’clock position and push 
it up so that it threads itself 
around the control dial.

6.

7.

Using a small screwdriver or 
pointed tool to help guide it, 
make sure the snap ring stays 
in the groove as it is inserted.

COPY

COPY

COPY

     

COPY 

xxxxx

SLICONE

LUBRICANT

Back of Cycler

Or top of cap

Summary of Contents for Pool XL Pro

















Reviews: