Fritz! Box 6490 cable Installation And Operation Manual Download Page 141

Page: 141 / 173

Help in Case of Errors

FRITZ!Box 6490 Cable

141

Help in Case of Errors

Here you can find assistance if you are not able to open the
user interface of your FRITZ!Box, or if errors occur with wire-
less LAN connections.

For more help, see the AVM Knowledge Base in the Internet:

en.avm.de/service

23.1

The User Interface Does Not Open

If the FRITZ!Box user interface cannot be opened, this can
have various causes.

Work through the following steps in sequence until the error
has been resolved.

Entering http://fritz.box in the Web Browser

Enter

http://fritz.box

in the web browser instead of

http://fritz.box

Google Chrome, for instance, performs a Google search if the
address of the FRITZ!Box is not known and entered incom-
pletely.

Restarting the FRITZ!Box

Disconnect the FRITZ!Box from the power supply.

Wait about five seconds before reconnecting to the pow-
er supply.

Wait until the LEDs “Power / Cable” and “WLAN” (only if
wireless LAN is switched on) light up.

The FRITZ!Box is ready for operation again.

Summary of Contents for Box 6490 cable














































































































































































Search results

Summary of Contents for Box 6490 cable

Reviews:

Related manuals for Box 6490 cable

Brands by name

Popular brands

Fritz! Box 6490 cable, Installation And Operation Manual

Search results

Summary of Contents for Box 6490 cable

Reviews:

Related manuals for Box 6490 cable

Brands by name

Popular brands