Fritsch PULVERISETTE 15 Operating Instruction Download Page 19 | Manualshive

Page: 19 / 19

Fritsch PULVERISETTE 15 Operating Instruction Download Page 19

pulverisette 15

page 16

7 Warranty

The warranty card accompanying this instrument must be returned to the
manufacturer, duly filled out, in order for the warranty to become effec-
tive.
We, Fritsch GmbH, Germany, our application technology laboratory and
our agent in your country will gladly provide advice and assistance with
this instrument.
Always include the serial number shown on the nameplate with any que-
ries.

8 Troubleshooting

Checklist

Functional error

Possible cause

Corrective measure

Mill fails to start

No power connected

Insert plug

Safety switch 1 open

Close cover properly

Safety switch 2 open

Fit collector properly

Rotor does not
turn

Blade gap incorrect

Readjust blade gap, see
section

4.1.2 Checking the

blade gap, 6.1 Removal
and fitting of cutting blades

Mill stops during
operation

Motor overheated

Check fan,
allow mill to cool

Overload,

Motor protection switch
actuated

Allow mill to cool,
clear of material,
reduce material feed rate

Poor milling re-
sult

Incorrect direction of
rotation

Check rotation:
Anticlockwise from drive
side

Material escapes Cover leaking

Replace seal

Tightening screw loose Tighten screw

Defective sealing ring

Replace sealing ring

Runs rough with
heavy vibration

Uneven setting of
rotary blades

Adjust rotating blades

Cutting rotor dirty

Clean cutting rotor

Feet standing uneven

Ensure machine stands
firm

Incorrect direction of
rotation

Check rotation:
Anticlockwise from drive
side

«
...
17
18
19

Summary of Contents for PULVERISETTE 15




















Reviews:

No comments