manualshive.com logo in svg

Fritsch ANALYSETTE 28 IMAGESIZER, Operating Manual

Share
Download
Fritsch ANALYSETTE 28 IMAGESIZER Operating Manual Download Page 26

26

Installation

4.9

Preparation of the computer

Computers provided by Fritsch GmbH are already equipped

with the software you need and can be used directly after the

device has been connected.

System requirements:

−

Intel Core i7 Quad Core processor or equivalent

−

Minimum of 8 GB system memory

−

Primary drive: minimum of 256 GB SSD

−

Secondary drive: 1 TB HDD

−

NVIDIA graphics card

−

USB 3.0 connection

−

22" monitor with 1920 x 1080 pixels resolution or better
Software:

−

Windows 7 or higher

−

Adobe PDF reader

1.

Insert the supplied USB stick into the USB port on your PC provided for this

purpose.

2.

Select the USB stick and run the CD_Start application on this.

There are various applications in the Prerequisites that

are needed for using the Image Sizing software. In

case they are not already on your PC, install also

‘.Net Framework 4.5’ and a version of ‘C++ 2015

Redistributable’.

3.

Then choose 

‘Image Sizing Software (ISS)’

.

4.

Install the 64-bit version of the USB driver. (If you have already installed the

newest FTDI-USB driver on your system, you do not need to install this in

addition.)

Summary of Contents for ANALYSETTE 28 IMAGESIZER































































Reviews:

No comments

Brands by name

Popular brands

Load more brands