manualshive.com logo in svg

Fritsch ANALYSETTE 28 IMAGESIZER, Operating Manual

Share
Download
Fritsch ANALYSETTE 28 IMAGESIZER Operating Manual Download Page 22

22

Installation

4.6

Electrical connection

DANGER

Provide short-circuit protection!
Risk of damage due to short-circuits.

−

Make sure that the socket is connected to a mains line

protected with a residual current circuit breaker.

DANGER
Mains voltage!
Changes to the connection line may only be made by a quali-

fied person.

Before establishing the connection, compare the voltage and current values

stated on the type plate with the values of the power supply system to be used.

CAUTION
Ignoring the values on the type plate may result in damage to

the electrical and mechanical components.

CAUTION
Ensure that the mains supply provides a functional device

ground connection!

4.6.1

Stability of the mains voltage

Instruments with electronic components require a stable supply voltage (+/-

10% deviation). For weak or non-interference free mains supplies (voltage peaks

through inductive load changes or switched-mode power supplies), we recom-

mend connecting via a voltage stabiliser and filter (Art. No. 20.6000.00).

4.7

Preparation of the ANALYSETTE 28 ImageSizer

Open the front flap (7) forwards by lifting up both latches (6).

Summary of Contents for ANALYSETTE 28 IMAGESIZER































































Reviews:

No comments

Brands by name

Popular brands

Load more brands