background image

 

 

 

 

Press the “FLAME” button to adjust flame brightness.  

 

 
Auto Safety Shut-Off Mechanism 
 

 

This fireplace is equipped with a safety shut-off feature which initiates if the fireplace overheats 

(e.g. Due to blocked air vents). For safety reasons, the fireplace will NOT automatically reset, 

and will need to be manually turned ON. 

 

To restart the fireplace, unplug the fireplace from the power outlet for at least 15 minutes. Next, 

reconnect to the power outlet and turn on the fireplace. 

 

Troubleshooting 
 

Problem

 

Possible Solution

 

 

 

Unit does not work / does not heat

 

 

·

 

Check if the unit is plugged in the power outlet. 

·

 

Check if the unit is in Standby mode. If so, turn 

the unit ON. 

·

 

Check if the heat is turned OFF. 

·

 

Check for safety cut-off operation.

 

 

 

No flame effect

 

 

·

 

Check if the unit is plugged in the power outlet. 

·

 

Check if the unit is in Standby mode. Turn the 

unit ON. 

 

Cleaning & Maintenance 
 

 

Disconnect from the power supply before attempting any maintenance or cleaning in order to 

reduce the risk of fire, electric shock to persons or damage to property. 

 

Warning

 - Always disconnect from the power supply before cleaning fireplace. 

 

For general cleaning, use a soft, clean duster.  Never use abrasive cleaners. The glass viewing 

screen should be cleaned thoroughly with a soft cloth. Do 

NOT

 use proprietary glass cleaners. 

 

Periodically check all fixings and tighten if necessary. 

 

The LED bulbs inside can NOT be replaced. 

 

Caution: Sharp edges! 

 

 
Technical Specification 
 

 

Supply: 120V

60Hz 

 

Rated Power: 1500W 

 

Bulb: LED (cannot be replaced) 

 

Summary of Contents for Venice WLVF-1/0343











Reviews: