Frigidaire PRFC2383AF Page 18 Use & Care Manual Download

Page: 18 / 50

WATER SUPPLY CONNECTION

IMPORTANT

Your refrigerator’s water supply system

includes several tubing lines, a water

filter, and a water valve. To ensure that

your water dispenser works properly,

this system must be completely filled

with water when your refrigerator is

first connected to the household water

supply line.



NOTE

These instructions do not cover after

market ice maker installation. Instruc-

tions in after market ice maker kit

should be used.

4. If you use copper tubing - Slide

brass compression nut, then

ferrule (sleeve) onto water supply

line. Push water supply line into

water valve inlet as far as it will

go (

inch/6.4 mm). Slide ferrule

(sleeve) into valve inlet and finger

tighten compression nut onto valve.

Tighten another half turn with a

wrench; DO NOT over tighten. See

Figure 1.

• If you use braided flexible stainless

steel tubing - The nut is already

assembled on the tubing. Slide nut

onto valve inlet and finger tighten

nut onto valve. Tighten another half

turn with a wrench; DO NOT over

tighten. See Figure 2.

5. With steel clamp and screw, secure

water supply line to rear panel of

refrigerator as shown.

6. Coil excess water supply line

(copper tubing only), about

turns, behind refrigerator as

shown and arrange coils so they

do not vibrate or wear against any

other surface. Do not kink tubing.

7. Turn ON water supply at shutoff

valve and tighten any connections

that leak.

8. Reconnect refrigerator to electrical

power source.

9. To turn ice maker on, ensure Ice

Maker is enabled on display (LED

will be lit) or set the ice maker’s

On/off power switch to the “ON”

position (freezer ice maker).

Figure 1

Steel

Clamp

Brass

Compression

Nut

Ferrule

(Sleeve)

Copper

Water line

Water Valve

Bracket

Valve Inlet

Water Valve

Copper waterline

from household

water supply

(Include enough tubing
in loop to allow moving

refrigerator out for cleaning)

Figure 2

Steel

Clamp

Valve Inlet

Water Valve

Braided

Flexible

Stainless

Steel

Water Line

(Include enough
tubing in loop
to allow moving
refrigerator out
for cleaning)

6 ft. (1.8 Meters)

Braided flexible

stainless steel water

line from household

water supply.

Summary of Contents for PRFC2383AF



















































Search results

Summary of Contents for PRFC2383AF

Reviews:

Related manuals for PRFC2383AF

Brands by name

Popular brands

Frigidaire PRFC2383AF, Use & Care Manual

Search results

Summary of Contents for PRFC2383AF

Reviews:

Related manuals for PRFC2383AF

Brands by name

Popular brands