background image

1.  Contact a specialist to install the device.
2.  Guarantee that the unit is appropriately fastened and complies with all of 
the aforementioned safety norms.
3.  Before operating the air conditioner, ensure that the air filter is installed 
correctly.
4.  If the unit has been out of use for a long period of time, it is recommended 
that the air filter be cleaned before use. During continuous use, clean the air 
filter every two weeks.
5.  This air conditioner was designed for use under the following conditions:

If air conditioner is used outside of the above conditions, certain safety protection 
features may come into operation and cause the unit to function abnormally.

Optimum performance will be achieved within these operating temperature.

Preparing the device for operation

Preparing the device for operation

Cool

MODE

Indoor

Indoor

Outdoor

Indoor

Outdoor

Attention

Dehumidifier

Temperature

Temperature

Temperature

Heat

Outdoor*

*

*

excess of this figure, the surface of the air conditioner may attract condensation.  

Room relative humidity should be less than 80%. If the air conditioner operates in  

Please set the horizontal louver to its maximum angle (vertically to the floor), and   
set HIGH fan mode.

61°F~86°

F

41

°F~1

15

°F  6

1

°F~86°F

6

1

°F~

86

°F

41

°F~1

15

°F

5

°F~

86

°F

*

23°F

~

115°F, for the models with low temperature cooling system

only for models with heating function

2

6

Summary of Contents for FRS09PYS1






















Reviews: