background image

5

INSTALLATION OF MOUNTING ASSEMBLY

A.   Evenly apply 1/2” thick rope of plumber’s putty around

      flange (1).

B.   Press Flange (1) firmly into sink drain.  Remove excess

      putty.

C.   Insert fiber gasket (2), backup flange (3) and mounting

      ring (5).  Hold in place while inserting snap ring (6).

YOUR DISPOSER COMES WITH THE FOLLOWING MOUNT SYSTEM

Mount System

READ COMPLETELY BEFORE STARTING

NOTE: Pay close attention to the order of mount assembly parts, as they have been correctly assembled by the factory.

D.   Place a weight such as a disposer on the sink flange to

      hold it in place.  Use a towel to prevent scratching sink.

      Pull snap ring open adn press firmly unitl it snaps into

      place.

E.   Tighten the 1 2/3” screws (3) evenly and firmly against

      backup flange.  Use shorter screws if sink is more than

      3/8” thick.

Grounding Instructions

FOR WASTE DISPOSERS EQUIPPED WITH A
GROUNDED PLUG-IN POWER CORD.

This appliance must be grounded.  In the event of a

malfunction or breakdown, grounding provides a path of

least resistance for electric current to reduce the risk of

electric shock.  This appliance is equipped with a cord

having an equipment-grounding conductor and a grounding

plug.  The plug must be plugged into an appropriate outlet

that is properly installed and grounded in accordance with all

local codes and ordinances.

FOR WASTE DISPOSERS NOT EQUIPPED WITH A
GROUNDED PLUG-IN POWER CORD.

This appliance must be grounded.  In the event of a

malfunction or breakdown, grounding provides a path of

least resistance for electric current to reduce the risk of

electric shock.  The power cord (to be installed) must have

an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordiances.  Disconnect electric power to

disposer circuit before installation.  Turn the circuit

breaker to the OFF position or remove the fuse.

Summary of Contents for Food Waste Disposer













Reviews: